Declaration Of Conformity; Environmental Protection - Norton Clipper CDM 163 Traducción Del Manual Original

Overload protection
To protect the motor, operator and diamond drill, the
machine is provided with a mechanical, electronic and
thermal overload safety system. Whenever the engine is
switched off due to overload, it must be switched on again
as soon as possible to cool the engine. Then let the drill
turn for a minimum of 1 minute.
1 - Electronic / Thermal
If the machine is being overloaded, the motor electronic
switches over to the pulsating operation for showing the
operator the overload. If the force is then not reduced, the
motor switches off after a few seconds. After switching the
machine off and on again, the motor start again softly.
2 - Mechanical
If the drill bit suddenly gets stuck, the slip coupling is
activated to disconnect the main axis from the engine.
Make sure you switch off the engine immediately and
remove the drill from the hole. When the slip coupling is
activated for a longer periods, the mechanical slip must be
re-tuned by a recognised expert.
Drilling with water cooling - Water connection
IF APPLICABLE
The drilling machine is equipped with a water tap, which
includes a 'Gardena' connection. Make sure that the core
drill is suffi ciently cooled and that the slurry is properly
discharged. The maximum permitted water pressure is 3
bars. Always use clean water to enlarge the life span of
the internal water seals. In case of leakage, the drilling
machine has to be checked IMMEDIATELY by a certifi ed
mechanical expert.
Dry drilling - Dust Extraction
IF APPLICABLE
For dry drilling only use designated drill bits. Dry drilling is
only possible in masonry, brick/block and sandstone.
Dust released during dry drilling is dangerous to your
health. Therefore a dust extraction system specially
intended for this purpose must be used, and if necessary,
a dust mask worn. The use of a dust extraction system
is also required to optimize the life time of the diamond
drill bit. To prevent clogging of the dust extraction system
it is essential that the materials which are being drilled are
completely dry. Information about dust extraction systems
is available at your diamond tools supplier.

ENVIRONMENTAL PROTECTION

According to the European regulation
2002/96/EC, SAINT-GOBAIN ABRASIVES
is responsible to recycle old electric drill
motors. You are therefore requested
to return old SAINT-GOBAIN ABRASIVES electric drill
motors to your local reseller.
WARRENTY
For the machine, a guarantee period of 12 months applies
from the moment of delivery. Guarantee claims must be
shown by submission of purchase invoice. The guarantee
includes the repair of defects which have occurred and can
be linked by to material or manufacturing faults.
Not covered by guarantee:
• Defects or damages which have arisen due to incorrect
use or connection.
• Machine overload.
• When maintenance has been carried out incorrectly or
badly.
• Information in the manual has not been properly followed.
• The machine is used by unqualifi ed persons.
• If the machine is used for purposes for which it is
unsuitable.
• The machine is repaired using unoriginal parts.
• If the machine encryption is damaged or deleted.
• If defects are caused by fi re, damp and/or transport.
EMISSION
Typically the A-weighted noise levels of the product are:
Sound pressure level 94 dB(A); Sound power level 105
dB(A). Uncertainty K = 3 dB.
WEAR HEARING PROTECTION!
The measured average vibration is less then 2,5 m/s²,
Measured values determined according to EN 60745.

DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product
(CDM 163 / CDM 203) is in conformity with the following
standards or standardized documents:
EN 60745-1; EN 55014; EN 61000;
2006/42/EC; 2004/108/EC
Machine Design Manager
Olivier Plenert
28.02.2014
SAINT-GOBAIN ABRASIVES S.A.
190, bd. J.F. Kennedy
L-4930 BASCHARAGE, LUXEMBOURG
ENGLISH – ORIGINAL INSTRUCTIONS
9