Assembly - Campbell Hausfeld AT122601 Instrucciones De Operación

Operating .Instructions
General Safety Information
(Continued)
(like a wooden pallet) a dry mat, or dry
carpet.
GeneRal SaFeTy
• . Read .all .manuals .included .
with .this .product .carefully . .
Be .thoroughly .familiar .
with .the .controls .and .the .
proper .use .of .the .equipment . .Follow .
all .instructions .
• . Only .persons .well .acquainted .with .
these .rules .of .safe .operation .should .
be .allowed .to .use .the .unit .
this product. Excessive exposure to
vibration, work in awkward positions,
and repetitive work motions can cause
injury to hands and arms. Stop using
any tool if discomfort, numbness,
tingling or pain occur, and consult a
physician.
1 . . Read .this .instruction .manual .before .
connecting .this .device .to .the .
compressor .
2 . . Safety .glasses .or .face .shield, .gloves .
and .a .NIOSH .approved .respirator .
must .be .worn .during .operation . .
Always .work .in .a .well .ventilated .
area .
Figure 1
3 . . During .operation, .do .not .expose .the .
hands .or .skin .directly .in .the .line .of .
the .blast .nozzle .
4 . . After .installation, .inspect .to .make .
sure .all .components .seal .properly .
5 . . Keep .children .away .at .all .times . .All .
visitors .must .be .kept .a .safe .distance .
and .wear .safety .glasses, .gloves .and .a .
respirator .
6 . . Do .not .exceed .the .maximum .
operating .pressure .of .the .
sandblasting .equipment .(125 .psi) .
www.chpower.com
Disconnect the sandblaster from the air
supply before changing accessories or
attempting to install, service, relocate
or perform any maintenance.
7 . . Check .hoses .and .air .lines .for .weak .
or .worn .condition .before .each .use . .
Make .sure .all .connections .are .secure .
MANUAL
before .use .
the sandblast gun at anyone or objects
other than the intended work object.
8 . . Do .not .depress .the .trigger .when .
connecting .the .air .supply .hose .
Do not
misuse
around oily rags or flammable liquids.
Sand striking metal can cause a spark
and create a fire or explosion.
Figure 2
acids or caustics.
Figure 3

assembly

MoDel aT122601
1 . . Attach .material .hose .to .the .pick-up .
tube . .Place .pick-up .tube .in .bag .of .
medium . .(See .FIgure .4) .
2 . . Attach .the .air .compressor .hose .
to .the .air .inlet .(1/4 .inch .NPT(F)) .
at .the .bottom .of .the .gun .handle . .
An .optional .quick .coupler .and .
Do not
point
Do not
work
Figure 4 - Model aT122601
MoDel aT125102
1 . . Attach .the .material .hose .to .the .hose .
Do not
spray
Figure 5 - Model aT125102
noTe: .Do .not .cover .the .hole .in .the .
hose .connector .for .dry .blasting . . .For .
spraying .liquids, .slip .the .material .hose .
fully .on .to .the .hose .connector .covering .
the .hole .
2 . . Attach .the .air .compressor .hose .
MoDel aT121002
1 . . Attach .the .hose .connector .to .the .
2 . . Attach .the .material .hose .to .the .hose .
2
connector .can .be .used .to .attach .the .
hose .to .the .gun .
Material .
hose
Do .not .cover .outer .
tube .with .hose .for .dry .
blasting
Pick-up .tube
connector . .Attach .the .opposite .end .
of .the .material .hose .to .the .gun .(See .
Figure .5) . .Never .use .hose .clamps .to .
secure .the .hose .
to .the .air .inlet .(1/4 .inch .NPT(F)) .
at .the .bottom .of .the .gun .handle . .
An .optional .quick .coupler .and .
connector .can .be .used .to .attach .the .
hose .to .the .gun .
hopper .using .the .supplied .conduit .
nut .
connector . .Attach .the .opposite .end .
of .the .material .hose .to .the .gun .(See .
Attach .air .
hose