[810] Wireless Option; [841] Visual Verification Programming; Placement Testing Wireless Devices (Lcd Keypads Only) - Tyco DSC PowerSeries neo HS2ICONX Serie Instrucciones De Instalación

NOTE: For UL Residential Burglary (UL1023), Home Health Care
(UL1637), ULC Residential Burglary (ULC/ORD-C1023) installations, the
maximum Supervision window shall be set to 24 hours.
For UL Residential Fire (UL985) installations, the maximum supervision
window is set to 200s.
For UL Commercial Burglary (UL1610/UL365) and ULC Residential Fire
(ULC-S545), the maximum supervision window shall be set to 4 hours.

[804][810] Wireless Option 1

To program wireless options:
1. Enter Installer Programming section [804][810].
2. Select one of the following options by scrolling or entering the hotkey.
Table 8: Wireless Options
On: the system cannot be armed if a wireless super-
RF Delin- visory trouble exists. An RF delinquency trouble is gen-
01
quency erated.
Off: wireless supervisory troubles do not prevent arming.
On: if a supervisory or jamming trouble occurs during
Wireless
Away arming, the siren activates and the event is
Supervisory/
02 logged and reported.
RF Jam
Off: supervisory or RF jam troubles during Away arm-
Alarm
ing do not activate the siren or get logged and reported.
Module On: module tampers are logged and reported.
03
Tamper Off: module tampers are not logged or reported.
On: fire devices are supervised every 200 seconds. If
the device fails to report within this window, a super-
vision trouble is generated.
Fire Super- Off: fire devices follow the supervision window pro-
04
vision grammed in section 802, up to a maximum of 18 hours.
The supervisory window can be programmed with a
higher value, but detectors still go into fault after 18
hours.
3. Press [*] to accept the selection and [#] to exit.

[804][841] Visual Verification Programming

To program wireless options:
1. Enter Installer Programming section [804][841].
2. Select one of the following options by scrolling or entering the hotkey
Table 9: Visual Verification Sub-Sections
On: Alarms trigger image capture from PIR Cam-
Visual Veri- eras
001
fication Off: Alarms do not trigger image capture from
PIR Cameras
01 Alarm + 5 Minutes
View Time Win-
002 02 Alarm + 15 minutes
dow
03 Alarm + 1 Hour
01 Fire key enabled/disabled
View Other 02 Duress key enabled/disabled
003
Alarms 03 Medical key enabled/disabled
04 Panic key enabled/disabled
[804][901]-[905] Delete Wireless Devices
To delete wireless devices:
1. Enter Installer Programming section [804] then select one of the fol-
lowing sub-sections:
Table 10: Module Label Sub-Sections
Sub-Section Description
901 Delete wireless zone devices
902 Delete wireless key
903 Delete sirens
904 Delete repeaters
905 Delete keypads
2. Select a device to delete using the scroll keys or go directly to a spe-
cific device by entering a hotkey.
3. Press [*] to delete or [#] to exit.
[804][921]-[925] Replace Wireless Devices
Use this option to replace a faulty device enrolled on the system with
another device of the same type while maintaining the configuration of the
original. The faulty device does not need to be deleted. To replace a wire-
less device:
1. Enter Installer Programming section [804] then select one of the fol-
lowing sub-sections.
Table 11: Replace Device Sub-Sections
Sub-Section Description
921 Replace wireless zone devices
922 Replace wireless keys
923 Replace sirens
924 Replace repeater
925 Replace keypad
2. Press [*] to select a sub-section. The first available device is dis-
played.
3. Select a device to replace using the scroll keys or go to a specific
device by entering a hotkey. Press [*]. When prompted, activate the device
(full enrollment) or enter the device ID (pre-enrollment). A message is dis-
played confirming enrollment.
[804][990][001- 005] Show All Devices
Use this section to review wireless devices enrolled on the system and to
view serial numbers associated with each device.
To review wireless device information:
1. Enter Installer Programming section [804][990] then select one of the fol-
lowing sub-sections:
Table 12: Wireless Device Sub-Sections
Sub-Section Descriptions
001 All zones
002 Repeaters
003 Sirens
004 Wireless keys
005 Keypads
2. Press [*] to select a wireless device type. The first available device is
displayed.
3. Use the scroll keys to view the enrolled devices.
NOTE: This option is not fully supported by LED and ICON keypads.
[904] Placement Testing Wireless Devices (LCD
keypads only)
This test is used to determine RF signal status for wireless devices and
can be performed at a system keypad or at the individual device. These
instructions pertain to testing at the keypad. For instructions on placement
testing at the device, refer to the installation sheet provided with the wire-
less equipment. The following test modes are available:001-128 – Test
wireless zones.