Publicidad
Idiomas disponibles
Idiomas disponibles
Storing a radio control for START/SEQ input
Keep button P3 pressed until LED DL8 starts to flash.
Release the P3 button and press the radio control you want to store. When LED DL8 stays switched on for about 1 second and
then switches off this means the radio control has been memorised. If, on the other hand, LED's DL7, DL8 and DL9 flash for about
3 seconds and then switch off this means the remote control has not been memorised because the maximum number of radio
controls has already been reached.
Deleting a radio control:
Keep button P3 pressed until LED DL8 starts to flash; do not release the button but wait until the flashing frequency increases; do
not release the button but wait until the flashing increases even further.
Release the P3 button and press the radio control you want to delete. When LED DL8 switches off this means the radio control
has been deleted.
Deleting all radio controls from the memory:
Switch off the device and switch it on again, keeping button P3 pressed. After a few seconds LED DL8 will start flashing very
quickly; keep the button pressed and do not release it for at least about 5 seconds, until LED DL8 switches off. At this point all the
radio controls will have been deleted from the memory.
Using output SPIA (9-10) controlled by remote control (also used as a 2
It is possible to use output SPIA(9-10) as a radio-controlled output, for every code it receives it remains ON for 1 second.
Power the control panel keeping button P2 pressed down and keep it pressed until LED DL9 stops flashing and stays switched
on all the time.
LED DL9 will stay switched on all the time to indicate that this output is being controlled by remote control.
To return to normal SPIA output (indicating that the gate is moving or open) repeat the instructions above until LED DL9 stays switched
off all the time.
Storing a radio control for output SPIA (9-10)
Keep button P2 pressed until LED DL9 starts to flash.
Release button P2 and press the remote control you want to store, LED DL9 will switch off for about 1 second and then switch on
again to confirm that the remote control has been memorised.
If, on the other hand, LED's DL7, DL8 and DL9 flash for about 3 seconds and then switch off this means the remote control has
not been memorised because the maximum number of radio controls has already been reached.
Deleting a radio control for output SPIA (9-10)
Keep button P2 pressed until LED DL9 starts to flash; do not release the button but wait until the flashing frequency increases; do
not release the button but wait until the flashing increases even further.
Release the P2 button and press the radio control you want to delete. When LED DL9 switches off this means the radio control
has been deleted.
N.B. Inputs that are normally closed (NC) should be bridged if they are not utilised.
If more than one NC contact is used on the same terminal, the contacts should be connected in series; if, instead, you use more than
one NO contact on the same terminal they should be connected in parallel.
1
Motor output: 2 positive 24Vdc,
2
1 negative 0Vdc
3
Flashing output: intermittent output 24Vdc max 10W,
4
5=0Vdc, 6=24Vdc
Out put boom light: the light blinks during boom
5
movement. When the barrier is closed, the light
6
blinks every 2 sec
7
Out put traffic light or 2° radio channel. Dry contact.
8
When barrier is open it is a close contact
9
Electric lock output maximum load (12Vdc mA 15VA)
10
11
24 VDC output, photocell power supply - accessories
12
14 + / 13 - (max 500mA)
15
Motor input for closing limit switch
16
NC contact, controls deceleration during closing.
15
Motor input for opening limit switch,
17
NC Contact , controls deceleration during opening.
PROGRAMMING:
To enter programming mode to program barrier travel keep button P1 pressed until LED DL7 starts to flash, and the lamp flashes very
quickly. If the learning sequence does not start within 10 sec LED DL7 will go off and
learning will be abandoned.
Start START/SEQ input: the barrier begins to open and after 3 seconds automatically closes.
When closing is completed the flashing lamp and LED DL7 switch on briefly. Programming ends when the flashing lamp and LED
DL7 go off.
Deceleration of the bar during opening and closing will start when the limit switches trigger.
WARNING:
During programming, a STOP impulse, triggering the photocell or pressing the P1 button for a second time will immediately halt the
programming procedure (LED DL7 will go off and learning will be abandoned).
+
4
nd
radio channel)
18
Sensitive EDGE/BORDO input (mechanical or resistive)
19
18
FOTO IN input, if ON prevents all opening and closing
20
movements
18
FOTO IN input, re-opens if barrier is closing, if ON
21
prevents all closing movements
22
STOP button input, stops all movement, if ON prevents
23
all movement
22
START/SEQ button input, controls:
24
Opening-stop-closing-opening.
22
CH/P button input, controls closing
25
22
OPEN/APRE button input, controls opening
26
Publicidad
