Lock-Off Button; Adjusting Blade Depth - RIDGID R8651 Manual Del Operador

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

OPERATION
WARNING:
Never tie the lower blade guard in a raised position.
Leaving the blade exposed could lead to serious
injury.
If at any time the lower blade guard does not snap closed,
remove the battery from the saw. Exercise the lower guard
by moving it rapidly back and forth from the full open posi-
tion to the closed position several times. Normally this will
restore the guard to its normal operating condition. If it does
not correct a slow or sluggish closing lower guard, do not
use the saw. Take it to an authorized factory service center
for repair.
KICKBACK
See Figures 6 - 9, page 16.
Kickback occurs when the blade stalls rapidly and the saw
is driven back towards you. Blade stalling is caused by any
action which pinches the blade in the wood.
WARNING:
Release switch immediately if blade binds or saw
stalls. Kickback could cause you to lose control
of the saw. Loss of control can lead to serious
personal injury.
To guard against kickback, avoid dangerous practices such
as the following:
 Setting blade depth incorrectly.
 Sawing into knots or nails in workpiece.
 Twisting the blade while making a cut.
 Making a cut with a dull, gummed up, or improperly set
blade.
 Supporting the workpiece incorrectly.
 Forcing a cut.
 Cutting warped or wet lumber.
 Operating the tool incorrectly or misusing the tool.
To lessen the chance of kickback, follow these safety
practices:
 Keep the blade at the correct depth setting. Less than a
full tooth of the blade teeth should be visible below the
workpiece.
 Inspect the workpiece for knots or nails before cutting.
Never saw into a knot or nail.
 Make straight cuts. Always use a straight edge guide
when rip cutting. This helps prevent twisting the blade.
 Use clean, sharp, and properly set blades. Never make
cuts with dull blades.
 Support the workpiece properly before beginning a cut.
 Use steady, even pressure when making a cut. Never
force a cut.
 Do not cut warped or wet lumber.
 Always let the blade reach full speed before beginning a
cut.
 Hold the saw firmly with both hands and keep your body
in a balanced position so as to resist the forces if kickback
should occur.
WARNING:
When using the saw, always stay alert and exercise
control. Do not remove the saw from the workpiece
while the blade is moving.

LOCK-OFF BUTTON

See Figure 10, page 16.
The lock-off button reduces the possibility of accidental
starting. The lock-off button is located on the handle above
the switch trigger. The lock-off button must be depressed
before you pull the switch trigger. The lock resets each time
the trigger is released.
NOTE: You can depress the lock-off button from either the
left or right side.
STARTING/STOPPING THE SAW
See Figure 10, page 16.
To start the saw:
 Depress the lock-off button.
 Depress the switch trigger.
Always let the blade reach full speed, then guide the saw
into the workpiece.
WARNING:
The blade coming in contact with the workpiece
before it reaches full speed could cause the saw to
"kickback" towards you resulting in serious injury.
To stop the saw, release the switch trigger.
After you release the switch trigger, allow the blade to come
to a complete stop. Do not remove the saw from the
workpiece while the blade is moving.
INDEXABLE LEVERS
See Figure 11, page 16.
The levers on the saw can be repositioned for the best
tightening position.
 Pull the lever out from the saw and to desired position.
 Push lever back into place.

ADJUSTING BLADE DEPTH

See Figure 12, page 17.
Always keep correct blade depth setting. Less than a
full tooth of the blade teeth should be visible below the
workpiece. More blade depth will increase the chance of
kickback and cause the cut to be rough.
10 - English

Publicidad

Tabla de contenido
loading

Tabla de contenido