IPC PW-C22 P Manual Del Usuario página 15

3 CONNECTION OF THE WATER SUPPLY PIPE
Based on the prescriptions and provisions
set forth by the regulations currently in
force, it is mandatory that the appliance
is never operated without a potable water
backflow preventer device, connected up to the
potable water supply mains. Use a suitable potable
water backflow preventer device, compliant to the
EN 12729 type BA standard provisions. Water that
flows through a system backflow preventer cannot
be classified as potable water.
Connect a clean water supply pipe to the
water mains, checking to ensure that the
minimum pressure is of 1.5 bar and maxi-
mum is of 6 bar, with a minimum flow rate
of 7 l per min.
- Connect the water supply pipe (min. diam ½") to
the water mains (Fig. 2)
- Screw the male connector (Fig. 3) on to the at-
tachment of the water supply (2); snap the female
connector of the tube (3) on to the connector.
4 HIGH PRESSURE PIPE CONNECTION
- Unwind the pressure hose off the hose drum (Fig.
4).
- Screw the high pressure tube on to the gun (Fig.
5).
5 ELECTRICAL CONNECTION OF THE AP-
PLIANCE
The mains voltage must match the operating volta-
ge. (See identification plate)
Insert the plug into a power socket installed in
compliance with regulations.
Check the minimum section of the individual cables
using extensions.
Position the extensions so as to maintain the pro-
tection class of the equipment.
Voltage Cable
V length m
230 up to 2
230 20 to 5
6 APPLIANCE ACTIVATION
Operate the equipment in vertical position
(Fig. 7) only after connecting the water
supply pipe and turning on the tap.
- Position the switch on I (ON) (Fig.8).
- Position the spray gun on the object to be
cleaned - never on people !
- Press the safety device (Fig.9) - the gun is released
- Direct the nozzle downwards (Fig.7)
- Fully press down the trigger (Fig.7)
- Position the switch on O (OFF) (Fig.8).
- Turn off water supply tap.
-
- Release trigger.
- Press safety latch on spray gun. (Fig.9). The
- Unplug machine from socket outlet.
- Disconnect water supply hose from machine and
Variable nozzle
The nozzle (Fig.10) can be regulated in a conti-
nuous manner, by rotating the regulation bushing,
changing it from a pinhole jet (Fig.10) to a flat jet
and viceversa.
It can be used at either high or low pressure by
shifting the head in a longitudinal sense according to
the direction of the arrow on the head itself (Fig. 11).
ADDITION OF DETERGENT
tank.Fill the detergent tank (Fig. 12) with detergent,
dilute as recommended.
Winder kit
The rotation sense for the winding of the high pres-
sure hose is only permitted in a clockwise direction.
(Fig. 13).
Cross-section
mm
2
1,5
Undertake only the maintenance operations descri-
2,5
bed in the user instructions.
Contact the Technical Assistance service for all other
interventions.
Use only original spares.
Should the power cable be damaged, it must be
replaced by a cable or a set of special cables avai-
lable from the manufacturer or its assistance service.
The pins and joints of the connection cables of the
electrical system must be protected against accidental
water sprays.
Cleaning/inspecting the strainer
Expose the strainer (Fig.14) in the machine water
15
7 SWITCHING OFF THE MACHINE
Actuate spray gun until water drips from the
nozzle (machine is now de-pressurized).
spray gun is locked and cannot be actuated
accidentally.
water supply mains.
8 ACCESSORIES
The detergents must not be allowed to
dry on the object to be cleaned.
The product is fitted with one detergent
9 MAINTENANCE , REPAIRS AND STORAGE
Before undertaking any work
on the appliance always de-
tachthe plug from the power
socket