Publicidad
Idiomas disponibles
Idiomas disponibles
EnGlIsH
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that Philips offers,
register your product at www.philips.com/welcome.
General description (Fig. 1)
A Beard trimming comb
B
Cutting unit
C Precision Zoom Lock ` adjustment ring
D Charging light
E
Socket for appliance plug
F
On/off slide
G Adapter
H Appliance plug
I
Cleaning brush
Important
Read this user manual carefully before you use the
appliance and save it for future reference.
Danger
-
Make sure the adapter does not get wet.
Warning
-
The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug, as
this causes a hazardous situation.
-
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
-
Children should be supervised to ensure that they
do not play with the appliance.
Caution
-
Use, charge and store the appliance at a temperature
between 5°C and 35°C.
-
Only use the adapter supplied.
-
Never immerse the appliance in water or rinse it
under the tap.
-
If the adapter is damaged, always have it replaced
with one of the original type in order to avoid a
hazard.
-
This appliance is only intended for trimming the
human beard. Do not use it for any other purpose.
-
Do not use the appliance if the cutting unit or the
beard trimming comb is damaged or broken, as this
may cause injury.
Electromagnetic fields
This Philips appliance complies with all standards
regarding electromagnetic fields (EMF). If handled
properly and according to the instructions in this user
manual, the appliance is safe to use based on scientific
evidence available today.
General
-
The appliance is equipped with an automatic voltage
selector and is suitable for mains voltages from 100
to 240 volts.
-
The adapter transforms 100-240 volts to a safe low
voltage of less than 24 volts.
Charging
Charge the appliance fully before you use it for the first
time.
It takes approximately 10 hours to fully charge the
appliance.
When it is fully charged, the appliance has a cordless
operating time of up to 35 minutes.
Note: You can use the appliance cordless as well as
connected to the mains.
1
Make sure the appliance is switched off (Fig. 2).
2
Insert the appliance plug into the appliance (Fig. 3).
3
Put the adapter in the wall socket.
The charging light on the appliance goes on to
,
indicate that the appliance is charging.
Note: The charging light does not change colour and does
not go out when the appliance is fully charged.
4
After charging, remove the adapter from the
wall socket and pull the appliance plug out of the
appliance.
2
Optimising the lifetime of the rechargeable
battery
When you have charged the appliance for the first time,
we advise you to use it until the battery is completely
empty.
Do not recharge the appliance in between the trimming
sessions.
Continue to use the appliance until the motor almost
stops running during a session. Then recharge the battery.
Follow this procedure at least twice a year.
Trimming
Always comb the beard and/or moustache with a fine
comb before you start trimming.
When you trim for the first time, be careful. Do not
move the trimmer too fast. Make smooth and gentle
movements.
Trimming with beard trimming comb
1
Turn the Precision Zoom Lock ` adjustment ring
to the desired setting. (Fig. 4)
See the table below for an overview of the settings and
the resulting hair lengths.
Setting
Resulting hair length
1
1mm
2
2mm
3
3.5mm
4
5mm
5
7mm
6
9mm
7
11.5mm
8
14.5mm
9
18mm
The setting appears in the window below the Precision
Zoom Lock ` adjustment ring.
Note: When you trim for the first time, start at the highest
setting (9) to familiarise yourself with the appliance.
2
Switch on the appliance.
3
To trim most effectively, move the trimmer against
the hair growth direction. Make sure the surface
of the comb always stays in contact with the
skin (Fig. 5).
4
If a lot of hair has accumulated in the beard
trimming comb, remove the comb and blow and/or
shake the hair out of it. The selected setting does
not change when you do this (Fig. 6).
Never pull at the flexible top of the beard trimming
comb. Always pull at the bottom part.
Trimming at the unique 'stubble look' setting
1
To create a 'stubble look', trim with the beard
trimming comb set to setting 1 (Fig. 7).
Trimming without beard trimming comb
Use the trimmer without beard trimming comb to trim
full beards and single hairs.
1
Pull the beard trimming comb off the
appliance (Fig. 8).
Never pull at the flexible top of the beard
trimming comb. Always pull at the bottom part.
2
Switch on the appliance.
3
Make well-controlled movements. Touch the hair
lightly with the trimmer (Fig. 9).
Corded trimming
If the battery is low, you can also use the appliance from
the mains:
1
Switch off the appliance, insert the adapter in the
wall socket and wait a few seconds before you
switch on the appliance.
Note: If the battery is completely empty, wait a few minutes
before you switch on the appliance.
Cleaning
Never use scouring pads, abrasive cleaning agents or
aggressive liquids such as alcohol, petrol or acetone to
clean the appliance.
1
Make sure the appliance is switched off and
disconnected from the mains.
2
Remove the beard trimming comb.
3
Open the cutting unit (Fig. 10).
4
Clean the cutting unit and the inside of the
appliance with the cleaning brush supplied (Fig. 11).
5
Push the cutting unit back onto the appliance to
close it ('click') (Fig. 12).
Note: The appliance does not need any lubrication.
Replacement
Only replace a worn or damaged cutting unit with an
original Philips cutting unit, available from authorised
Philips service centres.
1
Open the cutting unit.
2
Pull the old cutting unit upwards to remove
it (Fig. 13).
3
Insert the two lugs of the new cutting unit into the
guiding slots (Fig. 14).
4
Push the cutting unit back onto the appliance
('click') (Fig. 12).
Environment
-
Do not throw away the appliance with the normal
household waste at the end of its life, but hand it in
at an official collection point for recycling. By doing
this, you help to preserve the environment (Fig. 15).
-
The built-in rechargeable battery contains substances
that may pollute the environment. Always remove
the battery before you discard and hand in the
appliance at an official collection point. Dispose of
the battery at an official collection point for batteries.
If you have trouble removing the battery, you can
also take the appliance to a Philips service centre.
The staff of this centre will remove the battery for
you and will dispose of it in an environmentally safe
way. (Fig. 16)
Removing the rechargeable battery
Only remove the rechargeable battery if it is completely
empty.
1
Disconnect the appliance from the mains and let
the appliance run until the motor stops.
2
Undo the screw in the housing of the
trimmer (Fig. 17).
3
Separate the 2 housing parts with a
screwdriver (Fig. 18).
4
Cut the wires close to the battery holder with a
pair of household scissors (Fig. 19).
5
Remove the battery holder with the rechargeable
battery (Fig. 20).
6
Use a screwdriver to pry the battery off the
printed circuit board (Fig. 21).
Do not connect the appliance to the mains again after
you have opened it.
Guarantee & service
If you need service or information or if you have a
problem, please visit the Philips website at
www.philips.com or contact the Philips Consumer Care
Centre in your country (you find its phone number in
the worldwide guarantee leaflet). If there is no Consumer
Care Centre in your country, go to your local Philips
dealer.
4222.002.8019.3
Publicidad
