WEG CFW300 V3.0X Referencia Rápida página 22

QUICK REFERENCE OF PARAMETERS, ALARMS AND FAULTS
Param. Description
P956 SoftPLC Parameter 47
P957 SoftPLC Parameter 48
P958 SoftPLC Parameter 49
P959 SoftPLC Parameter 50
SoftPLC Parameter Configuration for PID Controller Application (P903 = 1)
Param. Description
P910 PID Controller Application Version
P911 Control Setpoint
P912 Control Setpoint 1
P913 Control Setpoint 2
P914 Control Setpoint 3
P915 Control Setpoint 4
P916 Control Process Variable
P917 PID Controller Output
P918 PID Controller Setpoint in Manual
Mode
P919 PID Controller Logical Status
P920 Selection of the Control Setpoint
Source
P921 Selection of the Control Process
Variable Source
P922 Minimum Sensor Level of the
Control Process Variable
P923 Maximum Sensor Level of the
Control Process Variable
P924 Value for Low Level Alarm for the
Control Process Variable
P925 Time for Low Level Fault for the
Control Process Variable
P926 Value for High Level Alarm for the
Control Process Variable
P927 Time for High Level Fault for the
Control Process Variable
P928 Selection of the PID Controller
Control Action
P929 PID Controller Operation Mode
P930 Automatic Adjustment of the PID
Controller Setpoint
P931 Proportional Gain
P932 Integral Gain
22 | CFW300
Adjustable Range
-9999 to 9999
-9999 to 9999
-9999 to 9999
-9999 to 9999
Adjustable Range
0.00 to 90.00
-99.99 to 99.99
-99.99 to 99.99
-99.99 to 99.99
-99.99 to 99.99
-99.99 to 99.99
-99.99 to 99.99
0.0 to 100.0 %
0.0 to 400.0Hz
0 to FFFF (hexa)
Bit 0 = Sleep Mode Active (A750)
Bit 1 = PID in Manual (0) / Automatic (1)
Bit 2 = PV Low Level (A760)
Bit 3 = PV Low Level (F761)
Bit 4 = PV High Level (A762)
Bit 5 = PV High Level (F763)
Bit 6 to 15 = Reserved
0 = Control Setpoint via
Communication Networks (P911)
1 = Control Setpoint via Analog Input AI1
2 = Control Setpoint via Analog Input AI2
3 = Control Setpoint via Electronic
Potentiometer (EP)
4 = Two Setpoints via Digital Input DI3
(P912 and P913)
5 = Three Setpoints via Digital Inputs DI3
and DI4 (P912, P913 and P914)
6 = Four Setpoints via Digital Inputs DI3
and DI4 (P912, P913, P914 and P915)
1 = Control Process Variable via Analog
Input AI1
2 = Control Process Variable via Analog
Input AI2
3 = Control Process Variable via Difference
between Analog Input AI1 and AI2
-99.99 to 99.99
-99.99 to 99.99
-99.99 to 99.99
0.0 to 999.9s
-99.99 to 99.99
0.0 to 999.9s
0 = Disable PID Controller
1 = Enable PID Controller in Direct Mode
2 = Enable PID Controller in Reverse Mode
0 = Manual
1 = Automatic
2 = Select Control to Manual (0) or
Automatic (1) via digital input DI2
0 = P911 inactive and P918 inactive
1 = P911 active and P918 inactive
2 = P911 inactive and P918 active
3 = P911 active and P918 active
0.00 to 99.99
0.00 to 99.99
Factory Setting
0
0
0
0
Factory Setting
2.00
2.00
2.30
1.80
1.60
0.0Hz
HMI or 0
1
0.00
4.00
1.00
0.0s
3.50
0.0s
0
2
0
1.00
5.00
Prop.
Prop.
ro
ro
ro
ro
cfg
cfg
cfg