Sunbeam 30810554 Guia De Inicio Rapido

Thank you for purchasing this Sunbeam
LED Under Cabinet Light Kit.
Please read all instructions before assembling and using your new cabinet light fixture.
IMPORTANT: FOR INDOOR AND DRY LOCATION USE ONLY. ADHESIVE TAPE MAY
DAMAGE SURFACE IF REMOVED.
DIMMER WAVE DETECTION SENSOR
Operation wave sensing range
≥ 5 cm / 2 in - ≤ 10 cm / 4 in
Wave hand once below the sensor to turn ON the LED light fixture.
Wave again below the sensor to turn OFF the LED light fixture.
After the light fixture is turned ON, dim the light by holding your hand under the sensor
until the desired light brightness is attained. Then lower your hand out of the sensing range to stop
dimming cycle.
Dimmer memory function: Unit maintains last dimmer setting when turned on.
NOTE: Dimming cycle will continuously dim from low to full brightness until your hand is away from
the sensor detection range.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS:
1. Use only insulated staples or plastic ties to secure cords;
2. Route and secure cords so that they will not be pinched or damaged when the cabinet is pushed to the wall;
3. Position the portable cabinet light with respect to the cabinet so the lamp replacement markings are able to be read
during re-lamping;
4. Not intended for recessed installation in ceilings, or soffits; and
5. The National Electrical Code (NEC) does not permit cords to be concealed where damage to insulation may go unnoticed. To prevent
fire danger, do not run cord behind walls, ceilings, soffits or cabinets where it may be inaccessible for examination. Cords should be
examined periodically and immediately replaced when any damaged is noted.
The low voltage portable cabinet light may be installed inside or under a kitchen cabinet or other built-in furniture when:
A) The low voltage Class 2 power supply is located outside the cabinet and is not concealed; and
B) The line voltage power supply cord is not concealed or run through openings in the cabinet, walls, ceilings, or floors.
This requirement does not apply to the wiring between the cabinet light and the power unit.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
MODEL # 30810554
30 cm / 12 in Wave Activated Dimmable
®
PARTS
LIGHT BEAM SPREAD
ITM. # 16325
Before installation, make sure the surface you intend to mount the product on is free of moisture,
oil, grease, dust and dirt to ensure proper adhesion. Test painted surfaces. Adhesive tape may
damage surface when removing.
STEP 1
There are 3 ways to mount the fixture.
A. Double-sided foam adhesive tape: Mark the
desired area where you want to install. Remove
one side of the tape and secure to the LED light
fixture. Then remove the other side of the tape and
secure to where you want to install. Continue to
step 3.
B. Drywall surface self-tapping screw:
Remove the small caps covering the 2 screw holes
on the LED light fixture (FIG. 1). Place the LED light
fixture over the desired mounting location and
mark the center of the holes to be drilled. Drill
two pilot holes 0.45 – 0.5 cm / 0.18 in – 0.20 in
diameter into the surface (FIG. 2). Insert the
anchors (FIG. 3). Place the LED light fixture over
the holes and screw in the self-tapping screws
1.9 cm / 0.75 in to secure (FIG. 4). Return the
small caps onto LED light fixture. (FIG. 5)
C. Wood surface self-tapping screw:
Remove the small caps covering the 2 screw holes
on the LED light fixture (FIG. 1). Place the LED light
fixture over the desired mounting location and
mark the center of the holes to be drilled. Then
place the LED light fixture over the marks and
screw in the self-tapping screws 0.95 cm / 0.37 in
to secure (FIG. 4). Return the small caps onto LED
light fixture. (FIG. 5)
FIG. 1
FIG. 3
FIG. 5
FIG. 6
FIG. 7
For information about ordering parts or how to expand your kit, please call us at 1-877-383-6399
(8:30 am – 5:30 pm E.S.T.) Monday - Friday or contact us at www.limagehomeproducts.com
If you have any problems, please do not contact the store.
Our customer service will be happy to assist you.
LIMITED WARRANTY This product is guaranteed to operate a minimum
of 3 years from the original date of purchase. If, under normal use and
for the full time period, your product fails to operate, please return it to:
Quality Control Dept., L'Image Home Products Inc., 15147 Don Julian Rd.,
City of Industry, CA., USA 91746 (with your original proof of purchase
receipt) and we will refund it. This warranty is considered void if the product
fails from misuse.
To download this instruction manual, visit the product page
on our website: www.limagehomeproducts.com
SAVE THESE INSTRUCTIONS
INSTALLATION
STEP 2
Connect the other LED fixtures to each other using
the direct connectors or jumper cable connectors.
(FIG. 6).
STEP 3
Connect the plug-in adaptor connector to the light
fixture. Then connect the AC / DC adaptor to the
LED light fixture by inserting the jack on the
adaptor into the round socket on the plug in
adaptor connector (FIG. 7).
STEP 4
Once you plug the AC / DC adaptor into the power
outlet, the LED light fixture is ready to be used.
STEP 5
Affix self-adhesive wire guides to desired
locations as needed to guide and secure jumper
cables and AC / DC adaptor cord.
Up to 4 x 30 cm / 12 in fixtures can be
connected with 24V / 0.62A adaptor
provided in this package.
FIG. 2
FIG. 4
MADE IN CHINA / FABRICADO EN CHINA
© 2018 Sunbeam Products, Inc. All rights reserved. SUNBEAM
trademark of Sunbeam Products, Inc. used under license. Distributed by L'Image
Home Products Inc., Montreal, Canada H3B 3X9.
NOTE:
Imported by:
L'Image Home Products Inc.
1175 Place du Frère André,
Montreal, QC, H3B 3X9
® logo is a registered
LHP1143-020818