Zoeller Home Guard MAX 503 Lista De Verificación Para La Preinstalación página 2

Manufacturer warrants, to the purchaser and subsequent owner during
the warranty period, every new product to be free from defects in material
and workmanship under normal use and service, when properly used
and maintained, for a period of two years from date of manufacture.
Parts that fail within the warranty period, that inspections determine to
be defective in material or workmanship, will be repaired, replaced or
remanufactured at Manufacturer's option, provided however, that by
so doing we will not be obligated to replace an entire assembly, the
entire mechanism or the complete unit. No allowance will be made
for shipping charges, damages, labor or other charges that may occur
due to product failure, repair or replacement.
This warranty does not apply to and there shall be no warranty for any
material or product that has been disassembled without prior approval
of Manufacturer, subjected to misuse, misapplication, neglect, alteration,
accident or act of God; that has not been installed, operated or maintained
in accordance with Manufacturer's installation instructions; that has
been exposed to outside substances including but not limited to the
following: sand, gravel, cement, mud, tar, hydrocarbons, hydrocarbon
derivatives (oil, gasoline, solvents, etc.), or other abrasive or corrosive
substances, wash towels or feminine sanitary products, etc. in all
pumping applications. The warranty set out in the paragraph above
1. The system is designed for installation in sumps with
minimum of 18" diameter and 22" deep. For smaller
applications, consult factory.
2. Remove all debris from the pit before installation.
3. Be sure that the pump is clamped securely to the
primary pump discharge pipe and that the two pumps
do not interfere with each other.
4. Install a serviceable check valve in the discharge line.
1. DO read all installation materials supplied with the
pump.
2. DO inspect unit for any visible damage caused
by shipping. Contact dealer if unit appears to be
damaged.
3. DO clean all debris from the pit before installation.
4. DO install a union check valve (see STEP 3) in the
discharge line. DO NOT use a discharge pipe smaller
than the recommended pump discharge sizes.
5. DO install a fi lter or strainer in the water supply line
before the pump to prevent small particles from
clogging the operating valve.
Limited Warranty
Helpful Hints For Easy Installation
Do's And Don't's For Installing A Unit
© Copyright 2011 Zoeller Co. All rights reserved.
is in lieu of all other warranties expressed or implied; and we do not
authorize any representative or other person to assume for us any
other liability in connection with our products.
Contact Manufacturer at, 3649 Cane Run Road, Lou is ville, Ken tucky
40211, Attention: Cus tom er Ser vice De part ment to obtain any need ed
repair or re place ment of part(s) or additional in for ma tion pertaining to
our warranty.
MANUFACTURER EXPRESSLY DIS CLAIMS LI A BIL I TY FOR
SPE CIAL, CON SE QUEN TIAL OR IN CI DEN TAL DAM AG ES OR
BREACH OF EX PRESSED OR IMPLIED WARRANTY; AND
ANY IMPLIED WAR RAN TY OF FIT NESS FOR A PAR TIC U LAR
PUR POSE AND OF MER CHANT ABIL I TY SHALL BE LIM IT ED TO
THE DU RA TION OF THE EX PRESSED WAR RAN TY.
Some states do not allow limitations on the duration of an implied
warranty, so the above limitation may not apply to you. Some states
do not allow the exclusion or limitation of incidental or con se quen tial
dam ag es, so the above lim i ta tion or exclusion may not apply to you.
This warranty gives you specifi c legal rights and you may also have
other rights which vary from state to state.
5. Install a fi lter or strainer in the water supply line before
the pump. Size the fi lter/strainer properly to minimize
pressure drop, while retaining particles at least 0.020"
(0.5 mm) in diameter.
6. Test the unit immediately after installation. Refer to
STEP 5.
7. Check the Float ON/OFF levels per STEP 2 of the
instructions.
8. Obtain model number, date code, and installation
instructions before calling factory.
6. DO test the pump immediately after installation to be
sure that the system is working properly.
7. DO review all applicable local and national codes and
verify that the installation conforms to each of them.
8. DO NOT use the Home Guard
DO NOT use the Home Guard
wastewater, sewage, effl uent, or water with debris in
it.
9. DO NOT use a garden hose. Garden hose is not
designed to hold municipal pressure indefi nitely
and could leak or burst causing fl ooding. The Home
Guard ® Max requires a permanent piping method such
as copper, PEX, or CPVC.
2
®
Max in hot water.
® Max to remove