RS V5868 Hoja De Instrucciones página 2

V5868
2
Blade Replacement
A. Perspective View
B. Carriage blade
C. Bottom blade
D. Side View
E. Ground surfaces
F. Line of cut
G. Feed bed level
Messerwechsel
A. Perspektive
B. Hubmesser
C. Gegenmesser
D. Seitenansicht
E. Geschliffene Flächen
F. Schnittlinie
G. Auflageebene
Mounting details
It is recommended that the shear is securely mounted by its fixing feet
before operations commence, with the rear of the shear facing a wall
to avoid approach to the rear of the machine. The shear should be
mounted on a table top via the 4 x 8mm fixing holes using 1⁄4 inch or
6mm screws with washers.
Dimensions 1 = 543mm, 2 = 492mm, 3 = 305mm.
Do Not Cut Steel
Materials
S.R.B.P. & Fibre glass boards, Aluminium brass.
Operating procedure
Ensure that the handle is firmly clamped to the top bar of the shear by
means of the handle wing clamp. With the handle in the vertical
position place the P.C.B. to cut on the feed bed against the reference
rule and align to the cutting size. Hold the P.C.B. with one hand and
pull the handle down slowly, the P.C.B. will firstly be clamped by the
clamp bar and then further down movement to the horizontal position
will then cut the P.C.B. Return the handle to the vertical position to
release the clamp holding the P.C.B.
2
B
y
C
h
g
a
b
c
Recambio de la cuchilla
A. Vista en perspectiva
B. Cuchilla móvil
C. Cuchilla inferior
D. Vista de perfil
E. Superficies de base
F. Línea de corte
G. Nivel de la placa de alimentación
Remplacement des lames
A. Vue en perspective
B. Lames mobile
C. Lame inférieure
D. Vue de côté
E. Surfaces meulées
F. Ligne de coupe
G. Biseau du plateau de pose
RS Stock No.
Replacement blades 609-405
A
x
f
d e
DK
Udskiftning af knivblade
A. Perspektiv
B. Øverste blad
C. Nederste blad
D. Fra siden
E. Arbejdsflader
F. Skærelinje
G. Niveau på skærebord
NL
Snijblad vervangen
A. Aanzicht met perspectief
B. Bovenste snijblad
C. Onderste snijblad
D. Zijaanzicht
E. Geslepen oppervlak
F. Snijlijn
G. Plaatsingsvlak
References
When cutting use reference rules and/or the sliding reference to stop
to give repeatable, accurate measurement to the cutting edge. Check
609-398
that the reference rules are right angles to the cutting edge by
releasing their clamping screws and aligning with an engineers try
square. Also ensure that the zero end of the rules align with the line of
cut without fouling the moving blade.
Slide the guide bars of the reference stop into the holes indicated in fig
1. Rest the lip of the reference stop on the feedbed surface and lock
the guide bars in the required reference position using the stop clamps.
The reference stop may also be used on the other side of the shear.
Blade replacement
Figure 2 shows perspective and side views of the blades and screw
assembly. Replace blades as follows:-
1. Remove operating handle.
2. Gain easier access to blades by unscrewing the plastic guard and
removing the clamp bar.
3. Remove the clamp bar by unscrewing the clamp rods (rotating
anticlockwise at the roll pin ends (fig. 1). Lift the rods out of the
carriage and extract the springs and clamp bar.
5. Release the three eccentrics f to h away from the bottom blade.
6. Remove both old blades by unscrewing screws a to e and five
carriage blade screws.
7. Clean the blade mounting surfaces of any accumulated dust, dirt
and debris. Clean excess grease from new blades.
8. Set new bottom blade onto its mounting surface ensuring the
cutting edge and taper is positioned as shown in the side view.
Loosely fit screws to a to e.
9. Fit and tighten new carriage blade with the leading edge and taper
as shown in the side view.
10. Lower the carriage blade until point x is just below feed bed level.
If necessary adjust the lower stops (fig. 1).
D
E F
G
SE
Skärbyte
A. Perspektivvy
B. Rörligt skär
C. Bottenskär
D. Sidovy
E. Slipade ytor
F. Klipplinje
G. Saxbäddens nivå