Rules For Safe Operation - Troy-Bilt TBSS Manual Del Operador

READ ALL INSTRUCTIONS BEFORE OPERATING
WARNING:
When using the unit, you must follow
the safety rules. Please read these instructions before
operating the unit in order to ensure the safety of the
operator and any bystanders. Please keep these
instructions for later use.
• Carefully read and understand the operator's manual of the
unit that powers this Add-On.
• Read this operating instruction manual carefully. Be thoroughly
familiar with the controls and the proper use of the equipment.
Know how to stop the unit and disengage the controls quickly.
• Do not operate this unit when tired, ill, or under the influence
of alcohol, drugs, or medication.
• Never allow children to operate the equipment. Never allow
adults unfamiliar with the instructions to use the unit. Never allow
adults to operate the equipment without proper instruction.
• All guards and safety attachments must be installed properly
before operating the unit.
• Inspect the unit before use.
• Clear the area before each use. Remove all objects such as
rocks, broken glass, nails, wire, or string which can be
thrown or become entangled in the attachment.
• Use only 0.080 inch (2.03 mm) diameter Genuine Factory Parts™
replacement line. Never use metal-reinforced line, wire, or rope,
etc. These can break off and become a dangerous projectile.
• This unit was not designed to be used as a brushcutter. Do
not attach or operate this unit with any type of brushcutting
blade or brushcutting attachment.
SAFETY WARNINGS FOR GAS POWERHEADS AND
STRAIGHT SHAFT TRIMMER
• Store fuel only in containers specifically designed and
approved for the storage of such materials.
WARNING:
Gasoline is highly flammable, and its
vapors can explode if ignited. Take the following
precautions:
• Always stop the engine and allow it to cool before filling the
fuel tank. Never remove the cap of the fuel tank, or add fuel,
when the engine is hot. Never operate the unit without the fuel
cap securely in place. Loosen the fuel tank cap slowly to
relieve any pressure in the tank.
• Mix and add fuel in a clean, well-ventilated area outdoors where
there are no sparks or flames. Slowly remove the fuel cap only
after stopping engine. Do not smoke while fueling or mixing fuel.
Wipe up any spilled fuel from the unit immediately.
• Avoid creating a source of ignition for spilled fuel. Do not
start the engine until fuel vapors dissipate.
• Move the unit at least 30 feet (9.1 m) from the fueling source
and site before starting the engine. Do not smoke. Keep
sparks and open flames away from the area while adding fuel
or operating the unit.
• Never start or run the unit inside a closed room or building.
Breathing exhaust fumes can kill. Operate this unit only in a
well ventilated area outdoors.
SAFETY WARNINGS FOR ELECTRIC POWER HEADS AND
STRAIGHT SHAFT TRIMMER
WARNING:
To reduce the risk of electrical shock,
use only extension cords approved for outdoor use,
such as an extension cord of cord type SW-A, SOW-
A, STW-A, STOW-A, SJW-A, SJOW-A, SJTW-W or
SJTOW-A. Extension cords are available from your
local retailer. Use only round-jacketed extension
cords approved for outdoor use.
2

RULES FOR SAFE OPERATION

• IMPORTANT SAFETY INSTRUCTIONS •
• CORD SETS: Make sure your cord set is in good condition.
When using a cord set, be sure to use a cord that is heavy
enough to carry the current that your unit will draw. An under-
sized cord set will cause a drop in line voltage resulting in loss
of power and overheating. See the operator's manual for the
unit that will power this add-on for the recommended cord size.
Extension
Straight Shaft
Cord Trimmer Cord
• Inspect all extension cords and the unit power connection
periodically. Look closely for deterioration, cuts or cracks in
the insulation. Also inspect the connections for damage.
Replace the cords if any defects or damage appear.
• Prevent disconnection of the straight shaft trimmer powerhead
from extension cord during operation by using a plug-receptacle
retaining strap, connector, or by making a knot as shown below:
• Avoid dangerous environments. Never operate your unit in
damp or wet conditions. Moisture is a shock hazard.
• Do not use the unit in the rain. Do not use in or around water.
• Do not handle the plug or unit with wet hands or standing on
any wet surfaces.
• Do not leave the unit plugged in when not in use, changing
attachments or add-ons, or while being serviced.
WHILE OPERATING
• Keep bystanders, especially children and pets, at least 50 ft
(15 m) away.
• Wear safety glasses or goggles that are marked as meeting ANSI
Z87.1 standards, and ear/hearing protection when operating this
unit. Wear a face or dust mask if the operation is dusty.
• Wear heavy, long pants, boots, gloves and a long sleeve shirt.
Do not wear loose clothing, jewelry, short pants, sandals or go
barefoot. Secure hair above shoulder level.
• Use the unit only in daylight or good artificial light.
• Use the right tool. Only use this tool for the purpose intended.
• Do not force unit. It will do the job better and with less
likelihood of injury at a rate for which it was designed.
• Do not overreach, take extra care when working on steep slopes
or inclines. Always keep proper footing and balance.
• Always hold the unit with both hands when operating. Keep a
firm grip on both the front and rear handle or grips.
• Keep hands, face, and feet at a distance from all moving parts.
Do not touch or try to stop the cutting attachment when it is
rotating. Do not operate without guards in place.
• Do not operate the engine faster than the speed needed to do
the job. Do not run the engine at high speed when not in use.
• Always stop the engine/motor when operation is delayed or
when walking from one location to another.
.• If you strike or become entangled with a foreign object, stop the
engine/motor immediately and check for damage. Have any
damage repaired before attempting further operations.
• Stop the unit IMMEDIATELY if you feel excessive vibration.
Vibration is a sign of trouble. Inspect thoroughly for loose
nuts, bolts or damage before continuing. Repair or replace
affected parts as necessary.
• Stop and switch the unit to off for maintenance, repair, or for
changing add-ons or other attachments. The unit must be
stopped and the cutting head no longer turning to avoid injury.
• Use only Genuine Factory Parts™ and accessories for this unit.
Extension Straight Shaft
Cord Trimmer Cord