Operational Safety; Operation And Safety - MetalTech I-IMCNAT Instrucciones De Operacion Y Emsamble

2

OPERATIONAL SAFETY

READ BEFORE BEGINNING ASSEMBLY.
FAILURE TO UNDERSTAND AND FOLLOW ALL SAFETY RULES AND ASSEMBLY INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH.
METAL CONDUCTS ELECTRICITY:
Do not use this equipment where contact may be made with power lines or other live electrical circuits.
DO NOT OVERLOAD:
This scaffolding is designed to support a maximum load of 500 lb (227 kg)
Per platform: 250 lb (113 kg) / Tool shelf: 35 lb (16 kg)

OPERATION AND SAFETY

Do not use this equipment if you are in poor health, taking
medications, drugs, or have been consuming alcohol, all of
which may impair your ability to work safely on this product.
Always use this scaffold in conformity with local or national
legislation which applies.
Inspect before use. Do not use if damaged. Check for missing parts.
Examine thoroughly to make sure unit is set up properly.
Always use casters secured to the structure with the locking pins.
A safe working deck must have a minimum
width of 18 inches (45.7 cm).
Do not climb unless the 4 casters are in locked position.
Erect to be plumb on firm and level surface.
Do not use the structure to climb up or down the scaffolding,
always use the platforms.
This scaffold must be used on a firm surface that is free
of pits, debris, holes or obstructions.
Never place anything under or attach anything to this scaffold to
increase height or to adjust to uneven surfaces.
Acids are corrosive and can seriously affect strength.
Do not expose this scaffold to corrosive substances.
Keep scaffold free of debris and unnecessary equipment.
Always keep body centered inside structure of scaffold.
Remove or fasten all tools, material or equipment before moving.
Use extra caution when moving to avoid tipping.
ALWAYS INSPECT
BEFORE USE
TOOL SHELF
MAX.
35 lb
MAXIMUM LOAD
(16 kg)
CAPACITY:
35 LB (16 KG)
DO NOT USE THE
STRUCTURE TO CLIMB
UP OR DOWN THE
SCAFFOLDING.
ERECT ON FIRM
AND LEVEL
GROUND
All photos and drawings in this booklet are for reference purposes only. Refer to applicable OSHA, ANSI or CSA codes and regulations for the proper use of this equipment.
Never try moving this scaffold while standing on it.
Never move a scaffold with worker within.
Do not use powered devices to propel this scaffold. Use extra
caution near operating machinery.
Do not use if the surface is not firm and level.
Do not use in inclement weather or high winds.
Maintain a firm grip while climbing.
Do not step or stand on the tool shelf.
Always ensure that the tool shelf is locked before using it.
Do not modify the scaffold or any of its component.
This scaffold is designed to be used by one person only.
Do not use the scaffold as a footbridge.
Use triple outlet adapter according to the product instructions
from the manufacturer.
Triple outlet adapter: Indoor use only. Keep out of water and
wet locations. Visually inspect all electrical equipment before
each use. Verify equipment conformity so that it doesn't present
electrical hazards. Always use an electrical grounded circuit.
MAX.
ALWAYS LOCK
1
THE FOUR CASTERS
BEFORE CLIMBING
METAL CONDUCTS
ELECTRICTY
DO NOT USE IN
INCLEMENT
WEATHER
OR HIGH WINDS
NEVER PLACE
ANYTHING UNDER
OR ATTACH
ANYTHING TO UNIT
THIS SCAFFOLD
IS DESIGNED
LB / KG
TO BE USED BY ONE
PERSON ONLY MAX. 500 lb
(227 kg)
ACIDS ARE
CORROSIVE.
DO NOT EXPOSE
UNIT TO CORROSIVE
SUBSTANCES
UNIT SHALL ONLY
BE USED ON FIRM
AND LEVEL
SURFACES
DO NOT USE
THE UNIT AS
A FOOTBRIDGE
SCAFFOLD
MAXIMUM LOAD
CAPACITY:
500 LB (227 KG)
250 LB PER PLATFORM
(113 KG)
ALWAYS KEEP BODY
CENTERED INSIDE
STRUCTURE OF UNIT
NEVER TRY MOVING
THE UNIT WHILE
STANDING ON IT
REMOVE OR FASTEN
TOOLS, MATERIAL OR
EQUIPMENT BEFORE
MOVING. NEVER MOVE
A SCAFFOLD WITH
WORKER WITHIN.