General Safety Information - Campbell Hausfeld IRONFORCE IFN00300 Manual De Instrucciones

Operating Instructions
General Safety
Information
(Continued)
Danger indicates
DANGER
!
an imminently
hazardous situation which, if not
avoided, WILL result in death or serious
injury.
• Read and understand
tool labels and manual.
Failure to follow
warnings, dangers, and
cautions could result in
DEATH or SERIOUS
INJURY.
• Do not use any type
of reactive gases,
including, but not
limited to, oxygen
and combustible
gases, as a power
source. Use filtered,
lubricated, regulated compressed air
only. Use of a reactive gas instead of
compressed air may cause the nailer
to explode which will cause death or
serious personal injury.
• Use only a pressure-
regulated compressed
air source to limit the
air pressure supplied
to the tool. The
regulated pressure
must not exceed 100
psi. If the regulator fails, the
pressure delivered to the tool must
not exceed 200 psi. The nailer could
explode which will cause death or
serious personal injury.
• Never use gasoline or
other flammable
liquids to clean the
nailer. Never use the
nailer in the presence
of flammable liquids
or gases. Vapors could ignite by a
spark and cause an explosion which
will result in death or serious
personal injury.
Nailer Components and Specifications
• REQUIRES: 0.8 SCFM with 10
nails per minute @ 90 PSI
• AIR INLET: 1/4 inch NPT
• NAIL SIZE RANGE: 3/8 inch to
1-1/4 inch
• MAGAZINE CAPACITY:
100 Nails per load, 18 gauge
• WEIGHT: 2 lb., 12 oz.
• LENGTH: 10.75 inch
• HEIGHT: 9 inch
• MAXIMUM PRESSURE: 100 PSI
• PRESSURE RANGE: 60 – 100 PSI
www.chpower.com
• Always remain in a
firmly balanced
position when
using or handling
the nailer.
• Do not remove,
tamper with, or
otherwise cause the
Work Contact
Element (WCE) or
trigger to become
inoperable. Do not
operate any tool
which has been modified in a like
fashion. Death or serious personal
injury could result.
• Do not touch
the trigger
unless driving
nails. Never
O
CO
attach air line
2
to nailer or
carry nailer
while touching
the trigger. The tool could eject a
fastener which will result in death or
serious personal injury.
WARNING
!
hazardous situation which, if not
avoided, COULD result in death or
serious injury.
100 psi
• Always
disconnect the
tool from the
power source
when
unattended,
performing any
maintenance or repair, clearing a
jam, or moving the tool to a new
location. Always reconnect the air
line BEFORE loading any fasteners.
Do not load the tool with fasteners
when either the trigger is depressed
or the Work Contact Element (WCE)
is engaged. The nailer could eject a
fastener causing death or serious
personal injury.
Quick clear nose
Work contact
element (WCE)
Nail discharge area
• Always fit tool
• Never place hands or
• Never carry the
Warning indicates
a potentially
• Always assume the nailer contains
• Do not drive a nail
Cap exhaust
Nail loading area
2
Model IFN00300
with a fitting
or hose
coupling on or
near the tool in
such a manner
that all
compressed air in the tool is
discharged at the time the fitting or
hose coupling is disconnected. Do
not use a check valve or any other
fitting which allows air to remain in
the nailer. Death or serious personal
injury could occur.
any other body parts in
the nail discharge area
of the nailer. The nailer
might eject a fastener
and could result in
death or serious
personal injury.
nailer by the air hose
or pull the hose to
move the nailer or a
compressor. Keep
hoses away from
heat, oil and sharp
edges. Replace any hose that is
damaged, weak or worn. Personal
injury or tool damage could occur.
nails. Respect the tool as a working
implement; no horseplay. Always
keep others at a safe distance from
the work area in case of accidental
discharge of nails. Do not point the
tool toward yourself or anyone
whether it contains fasteners or not.
Accidental triggering of the nailer
could result in death or serious
personal injury.
on top of other nails.
The nail could glance
and cause death or a
serious puncture
wound.
Trigger
Adjustable depth control
Magazine
Latch