Technical Parameters; Other Information - Elko EP PSB-10-12 Manual Del Usuario

Technical parameters

PSB-10-12 PSB-10-24
Input
AC 110 - 250 V / 50 - 60 Hz
Voltage range:
Burden without load (max.):
Burden with full load (max.):
Protection:
Output
Output voltage DC /
12 V / 0.84 A
max. current:
Tolerance of output voltage:
Output indication:
Wave of off -load output
voltage:
Wave of output voltage with
max load:
Time delay after connection:
Time delay after over-load:
Effi ciency:
Electronic fuse:

Other information

Working humidity:
Operating temperature:
Storage temperature:
Electrical strength input-output:
Protection degree:
Overvoltage category:
Polutioon degree:
Max. cable size (mm 2 ):
solid wire CY, 4x 0.75 mm
Connection wires
(AWG 18) / 90 mm (3.5")
(cross-section / lenght):
48 x 48 x 21 mm (1.9 x 1.9 x 0.8")
Dimensions:
Weight:
Standards:
Warning
Device is constructed for connection for 1-phase main alternating -current voltage and must be installed according to norms valid in existing state. Connection according to the details
in this direction. Installation, connection, setting and servicing should be installed by qualifi ed electrician staff only, who learn this instruction and functions of device. For right device
protection should be fronted-end certain element. Before starting installation must be main switch in position "SWITCH OFF" and device should be out of voltage. Don´t install device
to suppliers surcharge electro-magnetic interference. By right installation of device is provide good air circulate to don´t pass maximal operating temperature, in case of higher ambient
temperature and permanent working. For installation and setting use screw-driver cca 2 mm. The device is full-electronic - installation should be eff ected according to this. Function
without problems is too dependent on previous type of transportation, storing and manipulation. In case of any vestige of destruction, deformation, non-function or missing part, don´t
install and made claim to seller. Product may be, after passing operating time, disassemled, recycled or puted on protected tip.
PS-10-12
AC 184 - 250 V / 50 - 60 Hz
3 VA / 0.5 W 5 VA / 2 W
26 VA / 13 W 25 VA / 13 W
x fuse T1A
24 V / 0.42 A 12.2 V / 0.84 A
± 2 %
x
40 mV
380 mV
max. 1s max. 1s
max. 1s max. 1s
> 75 %
electronic protections short-circuit, over load, over voltage (from 120 % of rated output)
-40 .. 85 °C -40 .. 85 °C
IP30
x
2
90 x 17.6 x 64 mm (3.5x 0.7x 2.5˝)
70 g (2.5 oz) 62 g (2.1 oz.)
PS-10-24 PS-30-12
AC 100 - 250 V / 50 - 60 Hz
9 VA / 1 W
24.2 V / 0.42 A 12.2 V / 2.5 A
± 2 % ± 2 %
80 mV 30 mV
20 mV 80 mV
max. 5s
> 75 % > 82 %
20 .. 90 % RH
-20 .. 40 °C
4 kV
IP40 from front panel / IP20 terminals
II.
2
solid wire max. 1x 2.5, max. 2x 1.5 / with sleeve max. 1x 1.5 (AWG 12)
90 x 52 x 65 mm (3.5 x 2.1 x 2.6˝)
155 g (5.4 oz.)
EN 61204-1, EN 61204-3, EN 61204-7
PS-30-24 PS-30-R PS-100-12 PS-100-24
10 VA / 1.5 W 10 VA / 1.7 W
70 VA / 37 W
fuse T2A
12.2 V / 2.5 A
24.2 V / 1.25 A 24.2 V / 1.25 A 12.2 V / 8.4 A
± 3 %
green LED
40 mV
500 mV
max. 1s
max. 1s
> 81 %
-25 .. 70 °C
x
90 x 105 x 65 mm (3.5x 4.1x 2.6˝)
157 g (5.5 oz.) 157 g (5.5 oz.)
AC 100 - 250 V / 50 - 60 Hz
12 VA / 2 W
195 VA / 121 W
fuse T 3.15A
24.2 V / 4.2 A
± 2 %
1 V
40 mV
max. 3s
max. 0.5s
> 82 %
-40 .. 85 °C
367 g (12.9 oz.)
2 / 2