Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
TROUBLESHOOTING GUIDE
PR OBL E M C AU S E
PR OBL EM
Brush spark
1. Brush worn.
when switch
2. Other.
released.
TROUBLESHOOTING GUIDE - SAW OPERATION
PRO BL E M CA US E
P RO BLEM
Blade hits
1. Misalignment.
table.
Angle of cut
1. Miter table unlocked.
not accurate.
2. Sawdust under table.
Can not adjust
miter.
Cutting arm
1. Loose pivot points.
wobbles.
Cutting arm
1. Pivot bolt too tight.
will not fully
2. Pivot spring not replaced
raise, or blade
properly after service.
guard won't
fully close.
3. Sawdust build-up.
Blade binds,
1. Improper operation.
jams, burns
2. Dull or warped blade.
wood.
3. Improper blade size.
4. Wood is moving during cut.
1. Saw blade not round / damaged / loose.
Saw vibrates
or shakes.
2. Arbor bolt loose.
PARTS LIST
WARNING
When servicing use only KNOVA replacement parts. Use of any other parts may create a HAZARD or
cause product damage. Any attempt to repair or replace electrical parts on this Miter Saw may create a HAZARD
unless repair is done by a qualified service technician. Repair service is available at your nearest Knova Service Centre.
ORDER ONLY BY MODEL NUMBER AND PART NUMBER
I.D. No.
D e s c r i p t i o n
07WD SLIDE PLATE
083Y
COMPRESSION SPRING
083Z
CORD CLAMP
091S
COMPRESSION SPRING
0CES
COMPRESSION SPRING
0CPD CENTER BOLT
0D9A
ANCHOR BLOCK
0DHT
SPRING GUARD
0DVJ
BLADE WRENCH
0J4E
FLAT WASHER
0J4M
FLAT WASHER
0J58
FLAT WASHER
0J6A
FLAT WASHER
0J7G
FLAT WASHER
0JAZ
WAVE WASHER
0JB0
WAVE WASHER
0JBG
DISC SPRING WASHER
0JE7
C-RING
0JMN O-RING
0JMP
O-RING
0JNR
O-RING ROD
S i z e
Qty.
I.D. No.
3
0JPF
1
0JUJ
1
0JX9
0JZF
1
1
0JZN
1
0K2L
1
0K5C
1
0K74
1
0K7L
Ø6*13-1
2
0K7X
Ø12*21-1
1
0K8X
Ø5*14-1
4
0K9X
Ø8*16-2.5
1
0KA0
3/8*29/32-1/8
1
0KA9
WW-6
4
0KB7
WW-8
2
0KB8
Ø12
1
0KB9
1
0KD6
1
0KD7
1
0KD8
1
0KDF
22
SU G GESTE D CORRECT IV E A CTION
1. Replace Brushes. See MAINTENANCE section.
2. Contact Knova Service Centre.
SU G GESTE D CORRECT IV E A CTION
1. See ADJUSTMENT - Cutting Arm
Travel section.
1. See OPERATION
- Miter Angle Adjustment section.
2. Vacuum or blow out dust. WEAR EYE PROTECTION.
1. See ADJUSTMENT - Cutting Arm
Travel section..
1. Loosen pivot bolt lock nut (see adjustment section).
2. Contact the Servise Center.
3. See MAINTENANCE section.
1. See BASIC SAW OPERATION section.
2. Replace or sharpen blade.
3. Replace with 10 in. diameter blade.
4. Use hold down clamp to secure workpiece to table.
1. Replace blade.
2. Tighten arbor bolt.
D e s c r i p t i o n
HEX. HD. BOLT
HEX. SOC. HD. CAP BOLT
HEX. SOC. SET SCREW
HEX. SOC. SET SCREW
ARBOR BOLT
HEX. SOC. HD. CAP SCREW
CR. RE. COUNT HD. SCREW
CR. RE. TRUSS HD. SCREW
CR. RE. ROUND WASHER HD. SCREW
CR. RE. TRUSS HD. ROUND NECK SCREW
CR. RE. TRUSS HD. TAPPING SCREW
DRIVE SCREW
CR. RE. PAN HD. TAPPING SCREW
CR. RE. PAN HD. TAPPING SCREW
CR. RE. PAN HD. TAPPING SCREW
CR. RE. PAN HD. TAPPING SCREW
CR. RE. PAN HD. TAPPING SCREW
CR. RE. PAN HD. SCREW
CR. RE. PAN HD. SCREW
CR. RE. PAN HD. SCREW
CR. RE. PAN HD. SCREW
S i z e
Qty.
M6*1.0-25
3
M6*1.0-12
1
M6*1.0-10
1
M6*1.0-10
2
M8*1.25-20
1
M8*1.25-30
2
M6*1.0-16
1
M6*1.0-8
1
M6*1.0-16
2
M6*1.0-10
2
M5*12-12
1
Ø2.3-5
2
M5*12-20
2
M3*24-10
1
M4*18-16
2
M4*18-20
4
M5*16-10
1
M4*0.7-8
1
M4*0.7-10
6
M4*0.7-12
2
M5*0.8-45
4
Publicidad
Capítulos
Tabla de contenido
Solución de problemas
