Application; Specifications; Assembly; Precautions And Preparation - E/D/E 600 Manual De Instrucciones

Bedienungsanleitung · Operating instructions · Mode d'emploi
Istruzioni per l'uso · Gebruiksaanwijzing · Instrukcja obsługi
Manual de instrucciones
THANK YOU VERY MUCH FOR CHOOSING OUR MANUAL FURNITURE MOVER.FOR YOUR SAFETY AND
CORRECT OPERATION, PLEASE CAREFULLY READ THE MANUAL BEFORE USE.
NOTE: All of the information report herein is based on date available at the time of printing. The factory reserves
the right to modify its own products at any time without notice or incurring in any sanction. Please verify with the
factory for possible updates.
1.

Application

The manual furniture mover has been developed for lifting and shifting wooden furniture. Foe this reason, its side
supports are lined with felt and the platforms with rubber .The securing straps have also edge-protectors, to
prevent damage to the furniture.
Since the hydraulic furniture mover consists of two units, it is possible to move pieces of furniture of varying
lengths but a rectangular base using the minimum of space. Due to its weight, the anti-slip covering on the
platforms and the teeth on the platform tips, the piece of furniture will hold itself in position when the units are
standing vertically and lower supports are in contact with its sides.
The securing strap is an additional absolute necessity.
The hand crank is turned clockwise to lift the platforms and in the opposite direction to lower again.
Using an old crate, try a few "dry runs"with the transport units moving furniture with them.
If you operate properly, our hydraulic furniture mover will help you to move switch cabinets, furniture, and etc.
quickly and safely.
2.

Specifications

Load Capacity Lifting Height
600 kg 300 mm
3.

Assembly

Every transport unit consists of three separate component groups; the frame, the platform, and the lifting
mechanism.
First remove a platform from the box, and place it on the floor. Then insert the spindle mechanism through the
upper opening and the slot in the profiled guide rail, until the mechanism's locating projection is seated the in the
top of the guide rail. The upper side support and the crank of the mechanism must face in opposite directions. Do
not yet tighten the clamping screw of the guide rail.
Now slide the frame's guide rail over the upper sliding insert of the platform, inserting the spindle though the hole
in this until the frame is standing on its wheels on the floor. The gear housing will be pushed out of the guide
when the spindle contacts the lower sliding insert of the platform. Turn the crank clockwise to move the threaded
spindle down though the lower insert, until the locater of the gear housing is again seated in the guide and the
bottom of the housing is resting on the guide. Now, the clamping bolt may be tightened.
The second unit is assembled in the same way.
4.

Precautions and preparation

4.1 The floor must be absolutely level, smooth and clean. There must be no inclines or slops to be moved
over. Make sure that the floor and the floor covering are to stand up to the loading imposed by the wheel
and whether the can take the weight of the furniture being transported.
4.2 Check whether the piece of furniture to be transported contains any loose objects. These will have to be
removed, or secured against sloping out of position.
4.3 Check whether the piece of furniture is strong enough for the two opposite side to take the weight of the
piece via the transport units can hold the furniture to be transported without damaging it.
4.4 Find the weight of the piece of furniture to be transported. The maximum load of 600 kg/pair =300 kg for
each unit must not be exceeded.
4.5 Find the center of gravity of the furniture to be transported. Along the furniture base, it is the decisive for
the load that a single transport unit can beat, across the base, for the center of the transport unit, and, in
connection with the height, for the moment of tilting that occurs when moving the furniture. When in use,
the height of the center of gravity must not exceed 0.8m. the distance of the transport units to one
another must not be less than 0.5m and not gravity 4.0m (furniture of the securing straps).
4.6 Never use this equipment for towing behind a vehicle.
5.

Operation

Before use, the transport components should be checked for function, and for any damage. If there are visible
defects, the components should not be used. Damaged parts must be replaced.
Since the manual furniture mover consists of two parts, it is necessary for two persons to operate them.
Before transporting furniture, the platforms should be wound down to the floor until the transport units are
standing vertically. If the furniture to be transported has an overhang at the level of the upper support, this
supported may be screwed in or out, adjust it until the transport is standing level. If this adjustment option is not
E/D/E GMBH · EDE PLATZ 1 · 42389 WUPPERTAL · GERMANY
Lifting Plate Size New Weight
33kg
225×120mm
S E I T E | 8