Important Charging Notes; Installing And Removing The Battery Pack - BLACK&DECKER GCO182 Manual De Instrucciones

3. Plug the charger into any standard 120 Volt 60 Hz electrical outlet and let the
battery pack charge initially for 9 hours. After the initial charge, under normal
usage, your battery pack should be fully charged in 3 to 6 hours.
4. Disconnect the charger from the outlet, then disconnect the charger from the tool.
WARNING: Do not use the tool while it is connected to the charger.
NOTE: To remove the battery pack from the drill, press down on the release button
on the back of the battery pack (figure 2) and slide out.
INSTRUCTIONS FOR CUP CHARGERS:
1. Plug the charger into any standard 120 Volt 60 Hz electrical outlet.
2. Slide the charger onto the battery pack as shown in figure 3 and let the battery
pack charge initially for 9 hours. After the initial charge, under normal usage, your
battery pack should be fully charged in 3 to 6 hours.
3. Unplug charger, and remove the battery pack. Place the battery pack into the tool
until it "clicks" into place.
NOTE: To remove the battery pack from the drill, press down on the release button
on the back of the battery pack (figure 2) and slide out.

IMPORTANT CHARGING NOTES

1. After normal usage, your battery pack should be fully charged in 3 to 6 hours. If the
battery pack is run-down completely, it may take up to 6 hours to become fully
charged. Your battery pack was sent from the factory in an uncharged condition.
Before attempting to use it, it must be charged for at least 9 hours.
2. DO NOT charge the battery pack in an air temperature below 40°F (4,5°C) or
above 105°F (40,5 °C). This is important and will prevent serious damage to the
battery pack. Longest life and best performance can be obtained if battery pack is
charged when air temperature is about 75°F (24°C).
3. While charging, the charger may hum and become warm to touch. This is a normal
condition and does not indicate a problem.
4. If the battery pack does not charge properly—(1) Check current at receptacle by
plugging in a lamp or other appliance. (2) Check to see if receptacle is connected
to a light switch which turns power off when you turn out the lights. (3) Move
charger and battery pack to a surrounding air temperature of 40°F (4,5°C) to 105°
F (40,5°C). (4) If the receptacle and temperature are OK, and you do not get proper
charging, take or send the battery pack and charger to your local Black & Decker
service center. See Tools Electric in yellow pages.
5. The battery pack should be recharged when it fails to produce sufficient power on
jobs which were easily done previously. DO NOT CONTINUE using product with its
battery pack in a depleted condition.
6. To prolong battery pack life, avoid leaving the battery pack on charge for extended
periods of time (over 30 days without use). Although overcharging is not a safety
concern, it can significantly reduce overall battery pack life.
7. When the battery pack is inserted into the charger, the red "Charging Indicator" light
will come on indicating that there is contact between the battery pack and charger.
The light will stay on as long as the battery pack is in the charger and the charger is
plugged into a working outlet. It WILL NOT flash, go out or change to a different
color when the charging cycle is complete.
8. The battery pack will reach optimum performance after being cycled 5 times during
normal usage. There is no need to run the batteries down completely before
recharging. Normal usage is the best method of discharging and recharging the
batteries.
OPERATING INSTRUCTIONS

INSTALLING AND REMOVING THE BATTERY PACK

NOTE: Make sure your battery pack is fully charged.
To install the battery pack into the tool align the rails on the battery pack with the slot
in the base of the tool's handle and slide the battery pack firmly into the handle until
you hear the lock snap into place.
To remove the battery pack from the tool, press the battery pack release button (G) and
firmly pull the battery pack out of the tool handle (figure 2).
8