Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Styrofoam/Plastic
Fascia
Reinforcement
Hitch Shown In Proper Position
Equipment Required: Knife or small hand saw
Fastener Kit: F75162
Wrenches: 11/16, 3/4
Drill Bits: 1/2
Drill 1/2" hole after tightening
7/16" fasteners – (4) places
Figure 2
1
Qty. (4)
7/16-20 Hex Nut
2
Qty. (4)
7/16 Lockwasher
3
Qty. (2)
7/16-20 U-Bolt
1.
Lower spare tire.
2.
Trim styrofoam/plastic fascia support as shown in figure 3 for installation of u-bolts.
Note: Trimming of styrofoam/plastic necessary to insure proper seating of receiver on vehicle crossmember.
3.
Install u-bolts over vehicle crossmember at cutouts in styrofoam/plastic.
4.
Raise hitch into position, attaching loosley to u-bolts with lockwashers and nuts.
5.
Center hitch on vehicle.
Tighten 7/16-20 nuts to 55 lb.-ft. (75 N*M), hitch should fit flat against bottom of vehicle crossmember.
6.
Remove (4) fasteners which secure fascia to fascia mounting brackets. Push fascia up to allow access to drill thru (2) holes in
hitch bar into rear face of vehicle crossmember. Drill (2) holes thru hitch plate and into front face of vehicle crossmember.
7.
Install ½-13 X 4.00 GR5 hex bolts and hardened flat washers as shown. Install lockwashers and nuts.
8.
Re-install fascia mounting fasteners.
9.
Raise spare tire back into position.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2004, 2006 Cequent Towing Products
Installation Instructions
Fascia
Vehicle
Crossmember
Tighten all 1/2-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Dodge Durango
Chrysler Aspen
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2
Hitch Plate
Figure 1
4
Qty. (2)
5
Qty. (2)
6
Qty. (2)
7
Qty. (2)
Sheet 1 of 3
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
9000 (4082 kg)
6000 (2722 kg)
Approx.
11.25 Inside / Inside Gussets
Styrofoam/Plastic
Fascia
Reinforcement
Fascia support bracket
Hitch Bar
at centerline of vehicle
1/2-13 X 4.00 GR5 Hex Bolt
1/2 Hardened Flat Washer
1/2 Lockwasher
1/2-13 Hex Nut
N75162
9-22-06
Part Numbers:
75162
33082
87562
Max Tongue
WT (LB)
900 (408 kg)
600 (272 kg)
.750 Wide
cutout
measured
from edge
Figure 3
of gusset-
both sides.
Rev. B
Form: F205 Rev A 5-6-05
Publicidad
Manuales relacionados para Cequent Towing Products 75162
Resumen de contenidos para Cequent Towing Products 75162
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 N75162 9-22-06 Rev. B 2004, 2006 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 N75162 9-22-06 Rev. B 2004, 2006 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 de 3 N75162 9-22-06 Rev. B 2004, 2006 Cequent Towing Products Form: F205 Rev A 5-6-05...