Tabla de contenido
Publicidad
IMPORTANT
Please read
these
instructions carefully before you start to assemble this product
.
Please
carry
out
the
steps in
the order
set
out
in
these
instructions.
Keep
these
instructions
in
a
safe
place
for future
reference.
Safety advice
For
safety purposes we
strongly recommend the product to
be
assembled by at least
two
people.
Some parts may have sharp edges.
Please be
careful when handling components. Always wear
gloves,
eye
protection,
and long
sleeves
when assembling or performing any maintenance
on
your product.
Do
not
attempt
to assemble the product
in
windy or wet conditions.
Do
not
attempt
to assemble the product if you
are
tired,
have
taken drugs,
medications or alcohol, or if you
are
prone to dizzy
spells.
Dispose
of
all
plastic
bags safely
-
keep
them
away
from children's
reach.
Keep
children
away
from the assembly
area.
When using
a
stepladder or power tools, make
sure
that
you
are
following
the manufacturer's
safety advice.
Do
not climb or stand on the
roof.
Do
not hang or
lay
on the profiles.
Heavy articles should not
be
leaned against the poles.
Keep
roof
and
gutters
clear
of
snow,
dirt
& leaves.
Heavy snow load on
the roof
can make
it unsafe to stand below or nearby.
If
color
was
scratched
during
assembly it
can be
fixed.
Cleaning
instructions
In
order to
clean
the product,
use
a
mild detergent solution and
rinse
with
cold clean water.
Do
not
use
acetone, abrasive cleaners, or
other
special
detergents to
clean
the
panels.
Clean
the product once assembly
is
complete.
Before
starting
assembly
Choose
your
site
carefully before beginning
assembly.
The
ground
surface must
be
perfectly flat
and leveled and
have
a
solid
base such
as
concrete,
asphalt, deck
etc.
Sort the parts and check against the
content
parts
list.
Parts
should
be
laid
out
close at hand. Keep
all
small parts (screws etc.) in
a
bowl
so
they do
not get
lost.
Please
consult your
local
authorities if
any
permits
are
required prior to constructing the product.
Tools &
Equipment
T001
(Supplied)
Required
for
assembly
(in
addition
to the previously depicted tools)
1.8 wooden
beams,
minimum 6' long
(1.8 m)
2.
Concrete
3.
Digging equipment, compatible
with
the
soil
type
and
required measurements
4.
High step ladder,
minimum of
8
rungs (8' /
2.4 m)
During Assembly
UI
When
encountering the information
icon, please refer to the relevant
assembly step for additional comments and
assistance.
Attention
During assembly
use
a
soft surface
below the
parts to avoid scratches and
damages.
Please
make
sure
you install the panels
with the
UV
protected
side
out (marked with
"THIS
SIDE
OUT")
and remove the sticker
as
panels are in place.
Step
1:
Dig
two
(2)
holes
according to the specified measurements and make
sure
the
bottom
is
well tightened.
Plan
ahead
according to the placement
of the parking
as
shown
in
the drawing. Make
sure
the
pits'walls
are at
a
90°.
If
the ground
is
sandy and
digging proper
holes
is
impossible,
please
consult
a
local
expert
/
constructor.
Step
2:
Profiles
#8646
come covered
in
plastic film,
please
do not
peel at
this point, it
serves
to
protect the profiles from the concrete.
These
profiles
assist in
stabilizing the concrete casting,
and will
be
later assembled
in
the
roof.
Step
5:
Please use
wooden
beams
(not supplied) to
set
and hold the aluminum poles
in place,
make
sure
the profiles
are set at
a
depth of
19.6" (50 cm)
in
accordance
with
the former step
(4).
The
aluminum
poles
must
be
leveled
in all
directions.
Step 6:
Please
note and make
sure
the concrete casting
reaches
the line that
was
marked on
the profile at the previous
steps.
Step
7:
Please
wait for the concrete to
be
fully
set
and dry,
in
accordance
with the
manufacturer's instructions
and
depending
on
the weather conditions, before continuing with
the assembly!
Step 9:
Please
note the profile's direction.
Step 19: Optional: if you find it
difficult
to
tighten the
screws,
it
is
possible to
use
toggle
clamps before
tightening
the
screws. Make sure
the toggle clamps do not come
in
direct
contact with the powder coated profiles!.
Use
a
wooden plank
in
order to protect the profile
from bending.
Step 33:
In
order to
be
able to
tighten the
screws, use
a
high step ladder.
Be
careful!
Tighten
all screws at
the end of assembly.
Notice the marks on
each
step:
During assembly some
screws are
fastened fully
by
wrench while others
are
fastened just
after the whole carport
is
assembled and leveled.
Note:
Anchoring this product to the ground
is
essential to
its
stability
and rigidity.
It
is
required to complete this
stage
in
order for your warranty to
be
valid.
Publicidad
Tabla de contenido
