Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
3.4.3.3. ADJUSTMENT SYSTEM FOR PULSED – BIPULSED MIG/MAG WELDING. SYNERGIC PROGRAM.
Material display
Fe
Ar
SS
Ar
SS
Ar
SS
Ar
SS
Ar
Pulsed
CuSi
Ar
Al Si
Ar
Al Si
Ar
Al Mg
Ar
Fe
Ar
P1: SELECT PROCESS
PULSE
PULSE
Adjustment system of Pulsed/Bi-pulsed MIG/MAG setting parameters:
P1: ENTER/EXIT TO
PARAMETERS SETTING
MODE
SETTING PARAMETERS
GALA INVERMIG SYNER 230 MP Bi-PULSE
Display
Gas display
D1
P50
CO
18%
P51
2
P52
P53
CO
2%
P54
2
P55
P56
2%
P57
P58
P59
CO
2%
P60
2
P61
P62
2%
P63
P64
P65
P66
P67
P68
P69
P70
P72
P73
P74
P75
P76
CO
18%
P77
2
P78
Prog. nº.
P2: SELECT
WELDING
PROGRAM
Ar CO
2%
PULSE
2
E1: SELECT CYCLE
PARAMETER
D2:
Wire display
D2
D3
mm
in
min.
SG2 SG3
0,8
0,030
SG2 SG3
---
0,035
SG2 SG3
1,0
---
308 LSi
0,8
0,030
308 LSi
---
0,035
308 LSi
1,0
---
308 0_2 %
0,8
0,030
308 0_2 %
---
0,035
308 0_2 %
1,0
---
316 LSi
0,8
0,030
316 LSi
---
0,035
316 LSi
1,0
---
316 0_2 %
0,8
0,030
316 0_2 %
---
0,035
316 0_2 %
1,0
---
Cu Si3
0.8
0,030
Cu Si3
---
0,035
Cu Si3
1,0
---
AL Si5 %
1,0
---
AL Si5 %
---
0,045
AL Si5 %
1,2
---
Si 12%
1,2
0,045
AL MG5 %
1,0
---
AL MG5 %
---
0,045
AL MG5 %
1,2
---
NO Cu
0,8
0,030
NO Cu
---
0,035
NO Cu
1,0
---
Wire type
P3: SELECT WIRE
DIAMETER
Ss
1.0 mm
E2: ADJUST VALUE
D3:
e(mm)
max.
0,6
5
SG 2 / SG 3 Si 1
0,8
5
Splash reduction, thermal input.
0,8
5
Less deformation, cost reduction.
0,6
5
Cr Ni 19-9.
0,6
6
Cleaner beads, greater speed.
0,6
6
Great atmospheric corrosion resistance.
0,6
5
Cr Ni 19-9.
0,6
6
Smaller figuration and improvement of stability.
0,6
6
Greater responsibility applications.
0,6
5
Cr Ni 19-12.
0,6
6
Low carbon content.
0,6
6
Greater resistance in acids environments.
0,6
5
Cr Ni 19-12.
0,6
6
Smaller figuration and improvement of stability.
0,6
6
Greater responsibility applications.
0,6
3
Cu-Si wire for electrocoating welding.
0,8
3,5
Cu alloys and dissimilar joints.
0,8
3,5
Better corrosion resistance.
0,6
7
Recommended for Al alloyed with Si.
0,8
6
Good penetration and bath fluidity.
0,8
6
Excellent in repair applications.
0,8
7
Al Si 12% Aluminum wire alloyed with Silicon.
0,6
6
Recommended for Al alloyed with Mg.
0,6
9
Greater anticorrosion and mechanical properties.
0,8
9
Greater resistance in saline environments.
0,6
5
For welding of carbon steel.
0,8
5
Greater stability and less projections.
0,8
5
Greater lifecycle of consumables.
E2: SELECT
WELDING PIECE
THICKNESS
mm
P1: SAVE
PARAMETERS
SAVED
PARAMETERS
51
Remarks
E1: CORRECTING
WELDING
VOLTAGE (ARC
HEIGHT)
-30 % TO + 30%
%
Publicidad
Tabla de contenido
