About This Document; General Safety Precautions - STEINEL PROFESSIONAL RS PRO LED B1 Notlicht Manual Del Usario

GB

1. About this document

Please read carefully and keep in a safe place.
– Under copyright. Reproduction either in whole or
in part only with our consent.
– Subject to change in the interest of technical
progress.
Symbols
Warning of electrical hazard.
!
Hazard warning!
Reference to other information in the
...
document.
...

2. General safety precautions

Hazard from electrical power.
Working with electrical current may produce haz-
ardous situations. Touching live parts can result in
electrical shock, burns or death.
• Always follow the safety precautions and instruc-
...
tions given in this document.
- Work on mains voltage must only be performed
by qualified, skilled personnel.
- National wiring regulations and electrical
operating conditions must be observed
( : VDE 100, : ÖVE-ÖNORM E8001-1,
D A
: SEV 1000).

- The luminaire must not be installed in poten-
tially explosive atmospheres.
- During installation, the electric power cable be-
ing connected must be dead and remain dead.
- The light must be protected by a circuit breaker
(10 A).
- Connection to a dimmer will damage the
luminaire.
- No more than twenty RS PRO LED B1 lumi-
naires must be connected in series.
- Do not coat or stick adhesive film to the lumi-
naire.
- Select a non-vibrating site of installation to
ensure proper working order.
...
Hazard from LED light!
Looking directly into the LED light when it is ON
could damage your retina.
• Never look into the LED luminaire at short range
or for any prolonged period (> 5 minutes).
– The luminaire must not be installed in potentially
explosive atmospheres.
– Select a non-vibrating site of installation to en-
sure proper working order.
– No changes or modifications must be made to
the product.
!
Hazard from vapours or electrolyte fluid!
Vapours or electrolyte fluid may escape from the
rechargeable battery if it is damaged or used im-
properly. Coming into contact with them may result
in severe injury (e.g. loss of sight, acid burns).
• Never open the rechargeable battery enclosure
or the rechargeable battery itself.
• Do not allow vapours or electrolyte fluid to come
into contact with your eyes. In the event of con-
tact with eyes:
– Do not rub your eyes.
– Immediately rinse eyes with plenty of clean
water (such as tap water).
– Seek medical advice.
• Do not touch any electrolyte fluid that has
escaped.
• Immediately move product away from naked
flamed or sources of heat.
• Immediately remove contaminated clothing.
3. RS PRO LED B1 emergency light
Proper use
– Luminaire with emergency lighting function.
– Indoor LED SensorLight with integrated back-up
rechargeable battery that automatically provides
3 hours of LED emergency lighting in compliance
with EN 60598-2-22.
– Efficient, automatically controlled luminaire with
high-frequency sensor for detecting persons.
– Photoelectric sensor for identifying the room
situation.
– 12 –
Package contents / product features (Fig. 3.1)
Product dimensions (Fig. 3.2)
A Shade
B HF-sensor
C Emergency light test button
D Red LED
E Plug-in terminal
F Sealing plug
G Wall / ceiling mount
H Light-level setting
I Time setting
J Reach setting
K PE
L Chassis
M Sealing plug
Technical specifications for SensorLight
Dimensions (w x h x d) 300 x 300 x 67 mm
Voltage 230-240 V/50 Hz
Output 16 W LED
Additional switching capacities
Incandescent lamps, 800 W max. at 230 V AC
Fluorescent tube, 400 VA max. at cos j = 0.5,
inductive load at 230 V AC
4 x 60 W max., C ≤ 88 µF
at 230 V AC
Luminous flux 1200 lm (without diffuser)
Efficiency 75 lm/W (without diffuser)
Luminous flux (with shade/diffuser) PMMA plastic: 972 lm cool white / 950 lm warm white
Efficiency (with shade/diffuser) PMMA plastic: 60.75 lm/W cool white / 59.38 lm/W warm white
Luminous flux, emergency light
21 lm
(with shade)
Colour temperature approx. 3000 kelvin (warm white) / 4000 kelvin (cool white)
HF-system 5.8 GHz (responds to the tiniest movement regardless of temperature)
Detection angle 360° with 160° angle of aperture
Transmitter power approx. 1 mW
Reach 1-8 m all round, infinitely variable, can be limited in 4 directions
Max. area covered approx. 50 m²
Time setting 5 sec. - 15 min.
Twilight setting 2-2000 lux
IP rating IP 20
IK rating PMMA IK03
Protection class I
Temperature range 0° C to +40 °C
*1) Fluorescent lamps, low-energy lamps, LED lights with electronic ballast
(total capacity of all ballasts connected below the level stated).
N Shrouds for partially limiting range
O Emergency-light module
P Rechargeable batteries
Q Spacer for surface wiring
Storage / transportation
The emergency light module and luminaire should
be stored and transported separately from each
other. Requiring no connection to mains power, the
emergency light module is immediately ready for
operation and switches ON when it is plugged into
the luminaire. The emergency light module has no
OFF switch. This means means it should only be
installed more or less immediately before use.
*1)
– 13 –