Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
14. Insert casters into feet by placing stem of caster into holes provided. Apply pressure
and twisting motion until casters snap into place (Figure 29).
15. Place tool basket (Not standard with all models), with curved surface against tank, on
rear wheel dolly assembly (Figure 30).
19
18
23
24
22
27
28
Tank bottom
DOLLY, CARRIAGE HANDLE AND
BASkET ASSEMBLY
(Not standard with all models)
1.
Remove head from tank and place tank upside down on a flat surface.
2.
Place wheels on rear frame/axle assembly with extended hub of wheel towards dolly
frame and place cap nuts on axle. Secure with hammer.
3.
Insert caster socket into front frame and secure with phillips head screw.
4.
Place groove in front frame into lip of tank and position so frame is directly above inlet.
5.
Position grooves of rear frame into lip of tank and align so rear and front frames engage.
6.
Secure dolly frame to tank by placing machine screws up through holes in dolly frame.
Ensure head of screw is fully recessed in area provided. After machine screw is inserted,
tighten with flatwasher and hex nut.
7.
Insert caster in caster socket and apply downward pressure until caster snaps into
place.
8.
Return vacuum to upright position. Attach carriage handle to tank by inserting bolt
through the center hole of handle and tank, secure with nut provided. Attach side han-
dles with screws provided. Be sure to spread ends of carriage handle when assembling
to prevent damage to tank.
9.
Insert basket through center of carriage handle and slide into place.
ITEM NUMBER & DESCRIPTION
1. Cap nut
2. 8" wheel
3. Axle
4. Rear frame
5. Caster socket
6. front frame
11
2
5
1
3
6
10
9
4
8
Tank
Bottom of Tank
Machine
Screw
Flat
Washer
20
21
Template
B
A
A
B
Bottom of Tank
25
26
Arrow
A
29
30
2
1
7. #8 x 1/2" lg. Screw
8. 1/4 - 20 x 3/4" lg.
Machine screw
9. 1/4" flatwasher
10. 1/4 - 20 hex nut
11. Caster
8
7
Tank
Machine
Screw
ITEM
DESCRIPTION
1
Cap nut
2
8" Wheel
Dolly
3
Axle
4
Rear frame
Hex
Flat
5
Caster socket
Nut
Washer
6
front frame
7
#8 x 1/2" lg. Screw
1. Remove head from tank and place tank upside
8
1/4-20 x 3/4" lg. Machine screw
down on a flat surface.
9
1/4" flatwasher
10
1/4-20 hex nut
2. Place wheels on rear frame/axle assembly with
11
Caster
extended hub of wheel towards dolly frame and
place cap nuts on axle. Secure with hammer.
3. Insert caster socket into front frame and secure
6. Secure dolly frame to tank by placing machine screws
up through holes in dolly frame. Ensure head of screw
with phillips head screw.
is fully recessed in area provided. After machine screw
4. Place groove in front frame into lip of tank and
is inserted, tighten with flatwasher and hex nut.
position so frame is directly above inlet.
7. Insert caster in caster socket and apply downward
5. Position grooves of rear frame into lip of tank
pressure until caster snaps into place.
and align so rear and front frames engage.
8. Return vacuum to upright position. Attach carriage
handle to tank by inserting bolt through the center hole
of handle and tank, secure with nut provided. Attach
side handles with screws provided. Be sure to spread
ends of carriage handle when assembling to prevent
down on a flat surface.
2. Place wheels on rear frame/axle assembly with
extended hub of wheel towards dolly frame and
place cap nuts on axle. Secure with hammer.
3. Insert caster socket into front frame and secure
1. Metal tank handle
with phillips head screw.
4. Place groove in front frame into lip of tank and
2. Side tank handle
position so frame is directly above inlet.
5. Position grooves of rear frame into lip of tank
3. #10 x 3/4" Screw hex head
and align so rear and front frames engage.
3
5
SIDE TANk HANDLE ASSEMBLY
(Not standard with all models)
Attach side handles to tank with screws provided (Figure 31).
FOUR WHEEL HEAVY DUTY DOLLY
(Not standard with all models)
Tools required:
(2) 1/2 inch open end wrenches, (2) 7/16 inch open end wrenches, or a socket set and a
hammer.
1. Insert 2
1
/
inch long bolt through center hole in rear frame, attach split lockwasher and
2
nut and tighten securely.
2. Attach handle brace to back of rear frame with 5/8 inch long machine screws, lock-
washers, and nuts. (finger tighten only.)
3. Position main frame inside rear frame. Attach (2) 5/8 inch long machine screws, lock-
11
washers and nuts in both sides. Tighten securely.
4. Attach handle uprights, inside main frame (make sure buttons at top face inward) using
5
5/8 inch long machine screws, lockwashers and nuts. (finger tighten only.) Align holes
3
at top of handle braces with holes in handle uprights. Attach with 1
6
screws, lockwashers and nuts. (Tighten securely.)
10
5. Go back and tighten machine screws at bottom of uprights and braces.
9
6. Attach caster sockets (open end down) to front of main frame using 5/8 inch long
machine screws, lockwashers and nuts. Insert casters into sockets.
7. Slide basket adapters on handle.
8. See Figure 32 and Figure 33 for correct installation of adapters.
9. Attach handle onto uprights by pushing down and holding buttons in on uprights.
4
10. Place tank retaining bracket through slot and bolt in rear frame and screw on knob.
11. Slide bumper down over main dolly frame until it bottoms out.
Bottom of Tank
12. Place axle upright on a hard surface and hammer on (1) cap nut. Place (1) wheel on axle
and slide down to cap nut. Slide axle through rear of frame and slide on other wheel.
Before assembling cap nut on other end of axle, be certain dolly is assembled correctly.
PART NO.
(You may place tank on dolly and tighten knob of retaining bracket to be sure of correct
assembly.)
43002-99
13. After ensuring dolly is assembled correctly remove tank and place dolly on side with
24250-10
installed cap nut on hard surface and hammer second cap nut on axle.
24415-00
14. Place accessory basket on adapters and pull out on outer rim of basket and snap into
93921-00
place Figure 34.
75405-00
93920-00
15015-99
09029-99
32
07003-99
13001-99
Handle
67736-00
5
up through holes in dolly frame. Ensure head of screw
is fully recessed in area provided. After machine screw
is inserted, tighten with flatwasher and hex nut.
ITEM NUMBER & DESCRIPTION
7. Insert caster in caster socket and apply downward
pressure until caster snaps into place.
4. Bolt 1/4 - 20 x 1/2"
8. Return vacuum to upright position. Attach carriage
handle to tank by inserting bolt through the center hole
5. 1/4 - 20 hex nut
of handle and tank, secure with nut provided. Attach
side handles with screws provided. Be sure to spread
ends of carriage handle when assembling to prevent
damage to tank.
9. Insert basket through center of carriage handle and
slide into place.
1
ITEM
2
1
2
3
4
5
6
4
ASSEMBLY
7
ITEM
DESCRIPTION
1
Cap nut
2
8" Wheel
3
Axle
4
Rear frame
5
Caster socket
6
front frame
7
#8 x 1/2" lg. Screw
8
1/4-20 x 3/4" lg. Machine screw
9
1/4" flatwasher
10
1/4-20 hex nut
11
Caster
For 14" Diameter Tanks
6. Secure dolly frame to tank by placing machine screws
up through holes in dolly frame. Ensure head of screw
is fully recessed in area provided. After machine screw
is inserted, tighten with flatwasher and hex nut.
7. Insert caster in caster socket and apply downward
pressure until caster snaps into place.
8. Return vacuum to upright position. Attach carriage
handle to tank by inserting bolt through the center hole
of handle and tank, secure with nut provided. Attach
side handles with screws provided. Be sure to spread
ends of carriage handle when assembling to prevent
damage to tank.
9. Insert basket through center of carriage handle and
slide into place.
DESCRIPTION
PART NO.
Metal tank handle
20882-00
handle & hardware Pkg.
93555-96
(includes items 3-6)
Side tank handle
93551-00
#10 x 3/4" Screw hex head
15039-99
Bolt 1/4-20 x 1/2"
64012-99
1/4-20 hex nut
13001-99
31
1
/
inch long machine
4
PART N
43002-
24250-
24415-
93921-
75405-
93920-
15015-
09029-
07003-
13001-
67736-
Handle
Publicidad
Tabla de contenido
