Disposal Of The Product; Technical Specifications - Stobag MOVENO Tandem DWIR-E Instrucciones Y Advertencias Para La Instalación Y El Uso

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 18
5.6 - Setting force on closure: "RDC" function
Caution! - The "RDC" level can only be personalised after programming the limit positions "0" and "1", using the Semi-automatic procedure (paragraph 5.5).
01. Use the Up or Down button to move the awning to the point of mid-travel.
02. Press and hold the Up pushbutton until the aw n ing reaches limit position "0" (do not release the button).
03. Then, with the Ascent button still pressed, press the Descent button the number of times as the level to be selected (press each time for 1 second, with a pause
of 1 second before pressing again). With the Up button still pressed, wait until the awning completes the same number of movements (in the down direction) as
the new level set. The levels available are:
level 1 = maximum force (factory setting.) / level 2 = medium force / level 3 = minimum force
04. Then release the Up button.
01
02
5.7 - Deleting the entire memory
Caution! - This procedure deletes all data in the Con trol unit memory, including positions "0" and "1".
01. Use the Up or Down button to move the awning to the point of mid-travel.
02. Press and hold the Up and Down buttons simultaneously and wait for the awning to perform a short movement, after which release only one of the two buttons
03. With 3 seconds after the awning has performed the short movement, press the previously released button (in point 02) three times.
04. The release the other pushbutton.
01
02
Disposal of the product
This product constitutes an integral part of the automation system, therefore it
must be disposed of along with it.
As in installation, also at the end of product lifetime, the disassembly and scrapping
operations must be performed by qualifi ed personnel.
This product is made up of different types of material, some of which can be recy-
cled while others must be disposed of. Seek information on the recycling and dis-
posal systems envisaged by the local regulations in your area for this product cat-
egory. Caution! - some parts of the product may contain pollutant or hazardous
substances which, if disposed of into the environment, may cause
serious damage to the environment or physical health. As indicated
by the symbol on the left, disposal of this product in domestic waste
is strictly prohibited. Separate the waste into categories for disposal,
ac c ording to the methods envisaged by current legislation in your
area, or return the product to the retailer when purchasing a new version. Caution!
- Local legislation may envisage serious fi nes in the event of abusive disposal of this
product.
We hereby declare that this device conforms to the fundamental requirements and relevant provisions of the CE directives.
Declaration of conformity: www.stobag.com
www.stobag.com
03
x 1 = maximum force /
x 1 = forza massima /
"0"
x 2 = medium force /
x 2 = forza media /
x 3 = medium force /
x 3 = forza minima /
03
1
or
Power supply voltage: see specifi cations on the motor dataplate
Power absorption on standby: 0,5 W
Encoder resolution: 2,7°
Continuous operation time: 4 min
Operating temperature: -20°C
IP Protection rating: IP 44
Note:
– All technical characteristics refer to an ambient temperature of 20°C (± 5°C).
– STOBAG reserves the right to apply modifi cations to the product at any ti m e when
deemed necessary, while maintaining the same functionalities and in t ended use.
1/2/3
?
04
x 3
THE
END
Technical specifi cations
04
THE
END
English – 17

Publicidad

Tabla de contenido
loading

Tabla de contenido