Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
CLEANING & MAINTENANCE
Hand-wash
Clean your Brio after every use or in between a number of large
batches. Do not use metal utensils or harsh abrasives when cleaning
as this can damage the coating.
1.
Unplug the Brio and make sure it cools completely.
2.
Use a damp cloth to wipe the outside of the appliance.
3.
Clean the Mesh Tray, Mesh Racks, Drip Tray, Grill/Griddle Plate,
Rotisserie Basket, Rotisserie Skewer, Door, Silicone Cupcake
Liners, and Non-Stick Baking Pan with a nonabrasive sponge,
hot water, and mild detergent. Dry thoroughly.
4.
To clean the Probe, wipe it with a damp cloth or paper towel.
Allow the Probe to dry.
Tip: If there is residual food or particles on the Tray, Racks, Grill/
Griddle Plate, Rotisserie Skewer, Basket, or Baking Pan, add some
hot water and let the item soak separately for about 10 minutes
for easier cleaning. Then, use a soft cleaning brush to remove any
lingering food. Dry the parts thoroughly.
Dishwasher
Bottom rack: Mesh Tray, Mesh Racks, Drip Tray, Grill/Griddle Plate.
Top rack: Rotisserie Basket, Rotisserie Skewer, Silicone Cupcake
Liners, and Baking Pan.
Note: Water can get inside the Door if washed in the dishwasher.
It is recommended you hand-wash the Door.
IMPORTANT - Do not immerse the Brio and door in water or
attempt to cycle them through the dishwasher. The outer surface
may be cleaned by carefully wiping it with a damp dishcloth
or sponge. Make sure the Brio has cooled completely prior to
cleaning.
Removing the Door for Cleaning
The Door on the Brio is removable for easier, more thorough cleaning,
including the glass. To remove the Door and clean all of the parts:
1.
Make sure the Brio has completely cooled. Partially open the
Door (about 1 inch).
2.
Holding the Door handle securely, lift up. Clean both sides with a
damp cloth or paper towel and dry the door thoroughly.
In case of other problems, immediately unplug and
contact Customer Service Department.
1-877-689-2838 • help@nuwavenow.com
30
30
cleaning & maintenance
WARNING
Remove Door Glass for Cleaning
Storage
1.
Unplug the Brio and let it cool
down completely.
2.
Make sure that all the parts are
clean and dry.
3.
Store in a cool dry place.
Place the Door on a flat surface.
Using a Phillips screwdriver,
remove all screws.
Carefully lift up and remove the
glass from the center window.
Gently clean the glass with a
damp cloth or paper towel.
For tougher buildup, soak the
glass in water first, or run it
under warm water. Dry the glass
thoroughly and return all the
screws before replacing the Door.
Light Bulb Replacement
Turn off and unplug the Brio. Ensure that the Brio, bulb cover, and the
bulb have cooled completely. Unscrew the light bulb cover and light
bulb.
Note: You can order the light bulb by calling Customer Service at
1-877-689-2838 or help@nuwavenow.com. Use part number 38209.
The light bulb can also be purchased at your local
hardware store. The Brio uses an oven incandescent
light bulb 25W - 120/125 Volt -T6 E14 screw.
1 inch
Lift up the inner portion.
31
31
nuwavenow.com
nuwavenow.com
Publicidad
Tabla de contenido
