Chicco activ3 Instrucciones De Uso página 10

• Make sure that the carry cot is
correctly attached to the stroller
before placing the child inside.
• Keep the plastic bags away from
children to prevent suffocation
risks.
• Products exposed to direct sun-
light will heat up; let them cool
down before placing a child inside.
• The carry cot is not designed for
children to sleep for a long period
of time: this product is not a sub-
stitute for a cot.
• It is recommended to air the carry
cot in case it has been used for a
long time.
• Before carrying or lifting the base
shall be adjusted in the lowest
position.
• Head of the child in the carry cot
should never be lower than the
body of the child.
• The child restraint system must
be covered when the product is
used outside the car to make the
child sleep unattended.
CLEANING AND MAINTENANCE
CLEANING
Clean the fabric parts with a damp sponge and neutral
detergent. Please refer to the product's care label.
Routinely wipe clean plastic parts with a soft damp cloth.
Always dry the metal parts to prevent the formation of
rust if the carrycot has come into contact with water.
MAINTENANCE
Lubricate the moving parts only if necessary, with a light
application of a silicone based lubricant. Always dry the
metal parts to prevent the formation of rust. Do not
submerge the carrycot in water. Routinely wipe clean
plastic parts with a soft damp cloth. To avoid friction, en-
sure that the locking devices of the carrycot and pram
are free from dust or sand. Do not leave the product ex-
posed to the sun for a long period of time; it may cause
the fabric to fade.
CARRYCOT FEATURES
HOOD
The carrycot is equipped with a sun canopy and windbreaker
that can be adjusted to various positions.
MOUNTING AND REMOVAL
1- Check that the clips located on the end of the metal
arch are properly fastened to the buttons located on
the fabric part. The buttons are properly fastened if
the two ends of the metal arch (fig 1) are easily visible.
2- Insert the two metal ends in the B and C supports located
in the central part of the carrycot until you hear a click (fig-
ure 2A); fasten the four tabs of the rear arch (figure 2 B).
NB: The coupling system is located inside the plastic B
and C supports, the round button on the supports serve
only for removing the hood (see point 3).
3- To remove the hood, first pull out the 4 tabs of the
rear arch (figure 3A) and then remove the front arch
by pushing the two buttons located on the base of
the locking device (fig. 3B).
WARNING: Improper removal of the hood could result
in the tabs breaking.
HOW TO USE THE HOOD
4- Inside the hood, between the visor and the first seg-
ment, is a fabric ring that can be used for hanging soft
toys. It comes with handy hooks (figure 4 A).
There is an adjustable rear opening flap to guarantee
proper ventilation: Unzip it to open, and fold the fabric
panel on the upper part of the hood. (Figure 4B).
INTERNAL COVERING AND COVER
5- To fasten the internal covering to the carrycot: Slip the
plastic band located in the baby's head zone between
the styrofoam support and the body of the carrycot;
then fasten the two tabs in the baby's foot area under
the edge of the carrycot, as shown in figure 5A. Then
fasten the two lateral press studs and fasten the two
fabric strips with velcro in the centre of the area where
the baby's feet are (figure 5 B). The cover is then fitted
using the zip and by fastening the side clips of the fab-
ric to the hood (diagram 5c). Once it has been fitted, it
can be opened from both sides.
ADJUSTABLE BACKREST -
COMFORT SYSTEM
6- The backrest of the carrycot can be adjusted gradually.
To lift or lower the backrest use the wheel located on the
outer part of the carrycot near the baby' s feet (figure 6).
WARNING: It is advisable to ventilate the carrycot after
prolonged use.
CARRYING HANDLE
7- The carrycot comes with a comfortable carrying han-
dle that can be adjusted in three positions (fig. 7):
A) Transport
B) Middle
C) Rest
8- To put the handle in the vertical position, grasp it in
the centre and pull it upwards until you hear a click
(figure 8 A); to put the handle back in the rest position
press both buttons at the base of the handle at the
same time and then turn it downwards (figure 8 B).
WARNING: Do not transport the carrycot with the han-
dle in the middle or rest position, but only with the han-
dle in carrying position.
10