Incorrect Use Of The Machine; General Safety And Accident Prevention; Instalation; Classification According To The Atex Directive - Sagola DOBLE 250 Manual De Instrucciones

6.6. INCORRECT USE OF THE MACHINE

The machine was designed with the intention for
professional use only.
Any other use may cause damage to the machine
and/or create dangerous situations for which the
manufacturer can't be held responsible.
In particular:
The use of solvents containing chlorides or fluorides
of carbon and substances with a base of allogeneic
hydrocarbons is expressly prohibited.
In addition, the machine must not be used for
washing or greasing of objects designed to come into
contact with foodstuffs.
National laws regarding the use and disposal of
products used for cleaning and washing parts must
be observed, as well as the elimination of the machi-
ne itself.
6.7. GENERAL SAFETY AND ACCIDENT
PREVENTION
This machine must have as its primary objective for
the sole purpose for which it was expressly designed.
The manufacturer can't be held responsible for any
damage to people, animals and objects caused by
improper, erroneous or unreasonable use of the
machine.
INCORRECT INSTALLATION OF THE MACHINE
MAY CAUSE DAMAGE TO PEOPLE, ANIMALS OR
OBJECTS. THE MANUFACTURER CANNOT BE
CONSIDERED RESPONSIBLE
DAMAGES

7.1. ARRANGEMENT OF THE LIGHTING SYSTEM

The Client must make sure that there is suitable
lighting for the surroundings and that the lighting
conforms to the regulations in force. In particular, the
Client must arrange the positioning of lighting that
illuminates all the working area.
7.2. ARRANGEMENT OF THE PNEUMATIC
SYSTEM
The Client must arrange a line of filtered compressed
air supplied by a compressor that is suitable for the
consumption required. Do not use compressed air
that contains chemical products, synthetic oil with
organic solvents, salts or corrosive gases as they
can cause damage or malfunctioning. The line of
compressed air must arrive up to the supply points of
the machine. If the compressed air contains a large
amount of moisture, it may cause malfunctioning in
the valves and in the pneumatic components. Install
a moisture separator downstream from the compres-
sor to avoid this.
Disconnect the air supply to the machine before
performing any cleaning or maintenance.
In case of failure and/or malfunction of the machine,
turn off, not directly intervene; consult a service
center authorized by the manufacturer and use only
original spare parts.
The user is obliged to check the right environmental
conditions (For example, low temperatures or high)
where the machine is located, which may affect
performance and/or severely damaged.
The use of equipment with an open flame or welders
or manipulate incandescent materials near the
Double 250 is expressly prohibited.
It's expressly forbidden to place objects of sizes and
weights inadequate working on the floor.
6.8. ECOLOGY
The DOBLE 250 shouldn't be used for cleaning or
degreasing objects destined to be in contact with
food.
Should be respected the laws concerning the use of
products used in cleaning and washing parts and the
equipment DOBLE 250.

7. INSTALATION

7.3. CLASSIFICATION ACCORDING TO THE
ATEX DIRECTIVE
FOR THESE The machine conforms to the essential requisites of
the EU Directive 2014/34/UE, better known as ATEX
("Explosive atmospheres"). It is classified as group II
category 3 letter G system. The assessment procedu-
res of conformity, carried out by an internal factory
check, allow the installation of the machine in surroun-
dings where there may be potentially explosive atmos-
pheres due to the presence of gas, fumes or mist.
Preparation for extraction of gases.
For the compliance ATEX, the machine is equipped
with a system of forced evacuation of the fumes
generated during the operation.
The smoke evacuation takes place through a chim-
ney on the upper end of the machine and is powered
by a forced suction (venture effect) that is automati-
cally activated depending on the mode of operation
of the machine.
This chimney must then be connected to the general
workshop extraction or brought outside the workshop.
In this second case, the chimney connected to the
machine must cover at least a portion in the vertical
of 1 meter before being led outside.
- 26 -