BS POWER PACK Manual De Utilización página 23

• Clean the hood frequently, both internally and
externally, using a cloth dampened with water or
non-abrasive neutral liquid detergents.
• The lighting .system is designed for use during cook-
ing and not for the prolonged general lighting of the
room. The prolonged use of the lighting system signifi-
cantly decreases the average duration of the bulbs.
• Attention: the non compliance with the hood clean-
ing warnings and with the replacement and cleaning
of the filters entails risk of fires. One therefore recom-
mends keeping to the suggested instructions.
• Replacing the halogen light bulbs (Fig. 11A).
- Remove the light bulb from its holder, using a lever
motion at the front as indicated in Fig. 11.
- Pull out connector A.
- Remove spring C fixing the light bulb to holder B and
replace bulb D with a new one which has exactly the
same characteristics.
- Follow the above steps in the reverse order to reas-
semble the parts.
• Replacing LED lamps (Fig.11B):
If the appliance version is with LED lamps, the inter-
vention of a specialised technician is necessary to
replace them.
• COMMANDS: (Fig.12)
Push-button A = on/off lights switch
Push-button B = on/off cooker hood switch. The
appliance switches on at speed level 1, If the cooker
hood is on depress the push-button for 2 sec. to switch
off the cooker hood. If the cooker hood is at speed
level 1 it will not be necessary to depress the push-
button to switch the cooker hood off. Decreases the
motor speed.
Display C = indicates the motor speed level selected
and activates the timer.
Push-button D = switches on the cooker hood.
Increases the motor speed. Touching the key at 3rd
speed, the intensive function runs for 6' , then the ap-
pliance go back to work at the original speed. During
this function the display blinks.
Key E = The Timer times the functions on activation
for 15 minutes, after which they are switched off. The
Timer is deactivated by re-pressing Key E. When the
Timer is activated the decimal point must flash on the
display. The Timer cannot be activated if the intensive
speed is functioning.
The "clean air" function is activated by pressing key E
for 2 seconds when the appliance is switched off. This
switches the motor on for 10 minutes every hour at
the first speed. During functioning a rotary movement
of the peripheral segments must be visualised on the
display. When this time has passed the motor switches
off and the fixed letter "C" must be visualised on the
display until the motor re-starts after 50 minutes for
another 10 minutes and so on. Press any key apart
from the light keys to return to normal functioning.
Press key E to deactivate the function.
• Active carbon/grease filter saturation:
- When display item C flashes, at a speed where it
alternates with the letter F (e.g. 1 and F), the grease
filters must be washed.
- When display item C flashes, at a speed where it
alternates with the letter A (e.g. 1 and A), the carbon
filters must be replaced.
After the clean filter has been positioned correctly, the
electronic memory must be reset by pressing button
A for approximately 5 seconds, until the indication F
or A shown on the display C stops flashing.
• Bright Control (Fig.13) the key symbols are explained
below:
A = LIGHT
B = OFF
C = SPEED I
D = SPEED II
E = SPEED III
F = AUTOMATIC STOP TIMER - 15 minutes (*)
If your appliance has the INTENSIVE speed function,
from speed THREE, press key E for 2 seconds and it will
be activated for 6 minutes after which it will return to
the previously set speed. When the function is active
the LED flashes.
To interrupt it before the 6 minutes have elapsed, press
key E again. Some models allow activating this function
even with speed one and two.
By pressing key F for two seconds (with the hood
switched off) the "clean air" function is activated. This
function switches the appliance on for ten minutes
every hour at the first speed. As soon as this function
is activated the motor starts up at the first speed for
ten minutes. During this time key F and key C must
flash at the same time. After ten minutes the motor
switches off and the LED of key F remains switched on
with a fixed light until the motor starts up again at the
first speed after fifty minutes and keys F and C start to
flash again for ten minutes and so on. By pressing any
key for the exclusion of the hood light the hood will
return immediately to its normal functioning (e.g. if key
D is pressed the "clean air" function is deactivated and
the motor moves to the 2nd speed straight away. By
pressing key B the function is deactivated).
(*) The "AUTOMATIC STOP TIMER" delays stopping
of the hood, which will continue functioning for 15
minutes at the operating speed set at the time this
function is activated.
• Anti-grease/active charcoal filters saturation:
- When the A key flashes with a 2 second frequency
the anti-grease filters must be washed.
- When the A key flashes with a 0.5 second frequency
the active carbon filters must be replaced or washed
depending on the type of filter.
Once the clean filter has been put back one must reset
the electronic memory by pressing the A key for ap-
proximately 5 seconds until it stops flashing.
• COMMANDS:(Fig.14A)MECHANICAL_(Fig.14B) El-
liptic the key symbols are explained below:
A = LIGHT
B = OFF
C = SPEED I
D = SPEED II
E = SPEED III
G = MOTOR WORKING indicator
THE MANUFACTURER DECLINES ALL RESPONSIBIL-
- 23 -