Safety Precaution; Installation Instructions - BS SLIM ARS Manual De Utilización

GENERAL
Carefully read the following important information regarding
installation safety and maintenance. Keep this information
booklet accessible for further consultations.
The appliance has been designed for use in the ducting version
(air exhaust to the outside), filtering version (air circulation on
the inside ) .

SAFETY PRECAUTION

1. Take care when the cooker hood is operating simultaneously
with an open fireplace or burner that depend on the air in the
environment and are supplied by other than electrical energy,
as the cooker hood removes the air from the environment
which a burner or fireplace need for combustion. The negati-
ve pressure in the environment must not exceed 4Pa (4x10
bar). Provide adequate ventilation in the environment for a
safe operation of the cooker hood.
Follow the local laws applicable for external air evacuation.
Before connecting the model to the electricity network:
- control the data plate (positioned inside the appliance) to
ascertain that the voltage and power correspond to the network
and the socket is suitable. If in doubt ask a qualified electrician.
- If the power supply cable is damaged, it must be replaced
with another cable or a special assembly, which may be
obtained direct from the manufacturer or from the Technical
Assistance Centre.
2. WARNING !
In certain circumstances electrical appliances may be a
danger hazard.
A) Do not check the status of the filters while the cooker
hood is operating
B) Do not touch bulbs or adjacent areas, during or straight
after prolonged use of the lighting installation.
C) Flambè cooking is prohibited underneath the cooker
hood
D) Avoid free flame, as it is damaging for the filters and a
fire hazard
E) Constantly check food frying to avoid that the
overheated oil may become a fire hazard
F) Disconnect the electrical plug prior to any maintenance.
G) This appliance is not intended for use by young children
or infirm persons without supervision
H) Young children should be supervised to ensure they
do not play with the appliance
I) There shall be adequate ventilation of the room when
the rangehood is used at the same time as appliances
burning gas or other fuels
L) There is a risk of fire if cleaning is not carried out in
accordance with the instructions
This appliance conforms to the European Directive EC/2002/
96, Waste Electrical and Electronic Equipment (WEEE). By
making sure that this appliance is disposed of in a suitable
manner, the user is helping to prevent potential damage to
the environment or to public health.
The symbol on the product or on the accompanying
paperwork indicates that the appliance should not be treated
as domestic waste, but should be delivered to a suitable
electric and electronic appliance recycling collection point.
Follow local guidelines when disposing of waste. For more
ENGLISH
information on the treatment, re-use and recycling of this
product, please contact your local authority, domestic waste
collection service or the shop where the appliance was
purchased.

INSTALLATION INSTRUCTIONS

Assembly and electrical connections must be carried out
by specialised personnel.
• Electric Connection
The appliance has been manufactured as a class II, therefore
no earth cable is necessary.
The connection to the mains is carried out as follows:
BROWN = L line
BLUE = N neutral
If not provided, connect a plug for the electrical load indicated
-5
on the description label. Where a plug is provided, the cooker
hood must be installed in order that the plug is easily
accessible.
An omnipolar switch with a minimum aperture of 3mm between
contacts, in line with the electrical load and local standards,
must be placed between the appliance and the network in the
case of direct connection to the electrical network.
• The minimum distance between the support surfaces of the
cooking pots on the cooker top and the lowest part of the
cooker hood must be at least 65 cm.
If a connection tube composed of two parts is used, the upper
part must be placed outside the lower part.
Do not connect the cooker hood exhaust to the same conductor
used to circulate hot air or for evacuating fumes from other
appliances generated by other than an electrical source.
- In the case of assembly of the appliance in the suction version
prepare the hole for evacuation of the air.
(*) Warning: plastic spacer fitting.
This product may also be supplied with a plastic spacer O, which
should be fitted before the hood is installed (Fig.1C).
Fix the spacer to the hood using screws P (Fig.1C).
To assemble the unit correctly, align the front panel of the hood
with the wall cabinet and decide on the distance necessary to fill
in any space remaining between the hood and the wall.
Once the distance has been established, use a cutter to
remove the excess plastic (Fig.1C).
The following procedures must be performed before the
appliance is installed:
- To make the appliance easier to handle, pull out
undercarriage A (fig. 2).
- Remove grille C using the relevant buttons B (fig. 3).
This product may be installed in 2 different ways:
Type A installation, figure 4
- Installing the hood to the lower part of the wall cabinet
Type B installation, figure 5
- Installing the hood between two wall cabinets
- Installing the hood to the lower part of the wall cabinet
(Fig. 4A)
This type of appliance must be positioned underneath the
cabinet; before installation the front panel of the hood must
be aligned with the cabinet and fixed in place by tightening
the 4 screws D (suited to the type of cabinet) in the
corresponding holes E (fig. 4) (please refer to the
measurements indicated in fig. 1).
GB