Timer Operation; Timer On/Off - Haier HSU-24H03/Z Manual De Funcionalmiento

Operation
Floor fixing dimensions
of the outdoor unit
(Unit:mm)

TIMER Operation

Set Clock correctly before starting Timer operation
You can let unit start or stop automatically at following times: Before you wake up in the
morning, or get back from outside or after you fall asleep at night. HSU-09H03/R2(DB)
HSU-12H03/R2(DB)
HSU-12HB03/R2(DB)
HSU-18H03/R2(DB) HSU-12HD03/R2(DB)

TIMER ON/OFF

(1)After unit start, select your desired operation mode.
Operation mode will be displayed on LCD.
Fixing of outdoor unit
Power indicator on indoor unit lights up.
(2)TIMER mode selection
Press TIMER button to change TIMER mode.
Every time the button is pressed, display changes as follows:
Indoor Unit
ON OFF
TIMER ON TIMER OFF
Place, robust not causing vibration, where the body can be supported
Select your desired TIMER mode (TIMER ON or TIMER
sufficiently.
Place, not affected by heat or steam generated in the vicinity, where
OFF) ON or OFF will flash.
inlet and outlet of the unit are not disturbed.
Place, possible to drain easily, where piping can be connected with the
(3)Timer setting
outdoor unit.
Place, where cold air can be spread in a room entirely.
Press HOUR / button.
Place, nearby a power receptacle, with enough space around. (Refer
Every time the button is pressed, time increases 10 min.
to drawings).
If button is kept depressed, time will change quickly.
Place where the distance of more than lm from televisions, radios,
wireless apparatuses and fluorescent lamps can be left.
Every time the button is pressed, time decreases 10 min.
In the case of fixing the remote controller on a wall, place where the
If button is kept depressed, time will change quickly. Time
indoor unit can receive signals when the fluorescent lamps in the room
are lightened.
will be shown on LCD. It can be adjusted within 24 hours.
(4)Confirming your setting
After setting correct time, press SET button to confirm, "ON"
or "OFF" stops flashing
Time displayed: Unit starts or stops at x hour x min. (TIMER
ON or TIMER OFF).
Timer mode indicator on indoor unit lights up.
Before inserting power plug into receptacle, check the voltage without fail. The power source is the same as the corresponding name p
Install an exclusive branch circuit of the power.
To cancel TIMER mode
A receptacle shall be set up in a distance where the power cable can be reached. Do not extend the cable by cutting it.
Just press TIMER button several times until TIMER mode disappears.
Hints
After replacing batteries or a power failure happens, Time setting should be reset.
Remote controller possesses memory function, when use TIMER mode next time, just
press SET button after mode selecting if timer setting is the same as previous one.
To this unit, both liquid and gas pipes shall be insulated
as they become low temperature in operation.
Use optional parts for piping set or pipes covered with
equivalent insulation material.
The thickness of the pipe must be 0.8mm at least.
Fix the unit to concrete or block with bolts( 10mm) and nuts firmly and horizonta
When fitting the unit to wall surface, roof or rooftop, fix a supporter surely with na
or wires in consideration of earthquake and strong wind.
If vibration may affect the house, fix the unit by attaching a vibration-proof mat.
Selection of Installation Place
ON OFF
blank
TIMER ON-OFF
Power Source
Selection of pipe
9
113.5 583 113.5
Floor fixing dimensions
of the outdoor unit
(Unit:mm)
HSU-22H03/R2(DB)
ON/OFF
1
Place, which is less affected by rain or direct sunlight an
MODE
sufficiently ventilated.
Place, possible to bear the unit, where vibration and nois
not increased.
FAN
Place, where discharged wind and noise do not cause a
nuisance to the neighbors.
Place, where a distance marked
in the above figure.
SWING
SLEEP
LOCK
HSU-09H03/R2(DB)
HSU-12HB03/R2(DB)
HSU-12HD03/R2(DB)
Liquid pipe 6.35mm(1/4")
Gas pipe 9.52mm(3/8")
ON
Outdoor Unit
TEMP
SET
3
4
TIMER
3
is available as illustr
2
CLOCK
RESET
HSU-12H03/R2(DB)
HSU-18H03/R2(DB)
HSU-22H03/R2(DB)
6.35mm(1/4")
12.7mm(1/2")