DeWalt DE7464 Manual Del Usuario página 19

Mounting for use with DE7461 small sliding table
Required hardware parts: 2 L-shaped brackets (32), 2 short hex head
bolts (13), 2 long hex head bolts (14), 4 flat washers (19), 4 lock washers
(21), 4 nuts (16) (fig. H5).
• Mount 2 L-shaped brackets (32) for the outfeed table to the rear of the
machine using long hex head bolts (14), flat washers (19), lock washers
(21) and nuts (16) as shown (fig. H6). Make sure that the brackets are
at a right angle to the saw table.
• Leaving the outer left hole empty (from the woodworker's point of
view), align 2 holes in the rear rail (2) with the lower holes (33) in the
L-shaped brackets. The flat side of the rail should be facing up.
• Mount the rail to the brackets and the ripping support table using short
hex head bolts (13), flat washers (19), lock washers (21) and nuts (16).
Do not fully tighten.
• Mount the sliding table to the left-hand side of the machine.
Parallel the rails to the table top
Front rail (fig. H8)
• Use the fence face (34) to extend the table surface over the front rail (3).
• Using a ruler, measure the distance between the table top and the rail at
both ends of the table top. The distance should be equal at both ends.
• If adjustment is required, slacken the bolts (11) holding the brackets to
the saw. Tap the brackets using a soft hammer until the distances are
equal at both ends of the table top.
• Securely tighten the bolts.
Rear rail (fig. H9)
• Use the fence face (34) to extend the table surface over the rear rail (2).
• Measure the distance between the table top and the rail at both ends
of the table top. The distance should be equal at both ends.
• If adjustment is required, slacken the bolts (14) holding the brackets to
the saw. Tap the brackets using a soft hammer until the distances are
equal at both ends of the table top.
• Securely tighten the bolts.
Parallel the ripping support table to the table top (fig. E2, F3, H3, & H10)
the table height should be level with the table saw top.
• Use the fence face (34) to extend the table surface over the ripping
support table (fig. H10).
• Align the tables using a soft hammer until the surfaces are equal.
• Use the leveling hardware (fig. E2) to adjust along its length, gauging
against the front rail (3) (fig. H10).
• Securely tighten the fasteners on the support bracket holding the
ripping support table to the machine (fig. F3).
• Tighten the cap head screws in the top of the legs (fig. E2), the coach
bolts holding the front rail brackets (fig. H3), and the hex head bolts
holding the rear rail (fig. H6).
Mounting the motor cover (fig. I)
• Replace the motor cover (35) as shown.
• Mount the motor cover using the washers (36) and screws (37).
• Tighten the nuts holding the lower support rails (7) to the bottom of the
leg brace (4) and the right-hand side cross member (25).
Consult your dealer for further information on the appropriate accessories.
Maintenance
Your D WALT attachment has been designed to operate over a long
E
period of time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
13
Lubrication
Your attachment requires no additional lubrication.
Unwanted products and the environment
Take your attachment to an authorized D
be disposed of in an environmentally safe way.
• 30 DAY NO RISK SATISFACTION GUARANTEE •
If you are not completely satisfied with the performance of your
D WALT tool, simply return it within 30 days, complete as purchased,
E
to the point of purchase, for a full refund or exchange. Proof of
purchase must be produced.
• ONE YEAR FREE SERVICE CONTRACT •
If you need maintenance or service for your D
12 months following purchase, it will be undertaken free of charge at
an authorized D WALT repair agent. Proof of purchase must be
E
produced. Includes labour and spare parts for the attachments.
Excludes accessories.
• ONE YEAR FULL WARRANTY •
If your D WALT product becomes defective due to faulty materials or
E
workmanship within 12 months from the date of purchase,
we guarantee to replace all defective parts free of charge or, at our
discretion, replace the unit free of charge provided that:
• The product has not been misused.
• Repairs have not been attempted by unauthorized persons.
• Proof of purchase date is produced.
This guarantee is offered as an extra benefit and is additional to
consumers statutory rights.
For the location of your nearest authorized D
please use the appropriate telephone number on the back of this
manual. Alternatively, a list of authorized D
details on our after-sales service are available on the Internet at
www.2helpU.com.
E N G L I S H
WALT repair agent where it will
E
GUARANTEE
WALT tool, in the
E
WALT repair agent,
E
WALT repair agents and full
E
en - 4