Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
- Regularly clean the power tool's air vents. The
speed
motor's fan will draw the dust inside the housing and
ur ac-
excessive accumulation
your
of powdered metal may cause electrical hazards.
- Do not operate the power tool near flammable ma-
ot be
terials. Sparks could ignite these materials.
match
-Do not use accessories that require liquid cool-
ount-
ants. Using water or other liquid coolants may result in
ssory
electrocution or shock.
e. Ac-
Kickback and Related Warnings
of the
-Kickback is a sudden reaction to a pinched or snagged
sively
rotating wheel, backing pad, brush or any other acces-
h use
sory. Pinching or snagging causes rapid stalling of the
ls for
rotating accessory which in turn causes the uncon-
ar or
trolled power tool to be forced in the direction opposite
wires.
of the accessory's rotation at the point of the binding.
ct for
For example, if an abrasive wheel is snagged or
After
pinched by the workpiece, the edge of the wheel that
sition
is entering into the pinch point can dig into the surface
ne of
of the material causing the wheel to climb out or kick
ool at
out. The wheel may either jump toward or away from
the operator, depending on direction of the wheel's
movement at the point of pinching. Abrasive wheels
during
may also break under these conditions.
-Kickback is the result of power tool misuse and/or
nding
incorrect operating procedures or conditions and can
es or
be avoided by taking proper precautions as given
mask,
below.
n ca-
-Maintain a firm grip on the power tool and po-
frag-
sition your body and arm to allow you to resist
kickback forces. Always use auxiliary handle, if
pping
provided, for maximum control over kickback or
e dust
torque reaction during start-up. The operator can
rticles
ure to
control torque reactions or kickback forces, if proper
precautions are taken.
work
-Never place your hand near the rotating acces-
wear
sory. Accessory may kickback over your hand.
-Do not position your body in the area where
work-
power tool will move if kickback occurs. Kickback
cause
will propel the tool in direction opposite to the wheel's
sory.
movement at the point of snagging.
-Use special care when working corners, sharp
agged
edges etc. Avoid bouncing and snagging the ac-
nning
cessory. Corners, sharp edges or bouncing have a
ssory
tendency to snag the rotating accessory and cause
cces-
loss of control or kickback.
ol out
-Do not attach a saw chain woodcarving blade
or toothed saw blade. Such blades create frequent
your
kickback and loss of control.
ssory
Safety Warnings Specific for Sanding Operations:
y into
-Do not use excessively oversized sanding disc pa-
per. Follow manufacturers recommendations, when
selecting sanding paper. Larger sanding paper extend-
ing beyond the sanding pad presents a laceration hazard
and may cause snagging, tearing of the disc or kickback.
Additional safety warnings
-CAUTION: In order to prevent overheating do not
cover the appliance.
-Ensure that neither the air access nor exit become
either totally or partially covered by drapery, clothing,
etc., as this increases the risk of fire.
- Ensure that the voltage indicated on the rating label
matches the mains voltage before plugging in the ap-
pliance.
- Only use the appliance with the specific electric con-
nector provided.
- If any of the appliance casings breaks, immediately
disconnect the appliance from the mains to prevent
the possibility of an electric shock.
- Do not use the appliance if it has fallen on the floor,
if there are visible signs of damage or if it has a leak.
- CAUTION: Maintain the appliance dry.
- CAUTION: Do not use the appliance near water.
- Do not use the appliance with damp hands or feet,
or when barefooted.
- Do not wrap the power cord around the appliance.
- Do not clip or crease the power cord.
- Check the state of the power cord. Damaged or tan-
gled cables increase the risk of electric shock.
- Do not touch the plug with wet hands.
- Do not touch any of the appliance's moving parts
while it is operating.
- Do not sand any material containing asbestos.
Working with asbestos and/or silica wheel, the dust
produced is harmful for health. Prevent inhalation of
these types of dust by following the appropriate health
and safety regulations.
- Protect yourself from contact with and the inhalation
of dust created by sanding wood and metal surfaces
and surfaces coated with lead paint. Use protective
equipment that complies with the appropriate health
and safety regulations.
- Exercise precaution after employing the stop opera-
tion on the appliance as the tool will continue moving
from the effect of its own mechanical inertia.
- Fully unroll the appliance's power cable before each use.
- Check the position of power cables before com-
Check the position of power cables before com-
mencing work ensuring they are well away from the
work area.
- Keep hands and other body parts well away from the
work area whist the tool is in use.
- Do not use the appliance if its accessories are not
properly fitted.
5
Publicidad
Tabla de contenido
