EMKO ESM-3723 Serie Manual De Instrucciones página 10

Hysteresis Parameter for Temperature ( Default = 0.1 °C )
From 1 to 10°C for NTC,PTC, PT-100 (0°C, 100°C)
From 1 to 18°F for NTC,PTC ,PT-100 (32°F, 212°F)
From 0.1 to 10.0°C for NTC, PTC, PT-100 (0.0°C,100.0°C)
From 0.1 to 18.0°F for NTC, PTC, PT-100 (32.0°F,212.0°F)
From 1 to 10°C for ProNem Mini PMI-P (-20°C, 80°C) ,From 1 to 18°F for ProNem Mini
PMI-P (-4°F,176°F),From 0.1 to 10.0°C for ProNem Mini PMI-P (-20.0°C,80.0°C)
From 0.1 to 18.0°F for ProNem Mini PMI-P (-4.0°F,176.0°F).
In ON/OFF control algorithm, temperature
value is tried to keep equal to set value by
opening or closing the last control element.
ON/OFF controlled system, temperature
value oscillates continuously. Temperature
value's oscillation period or amplitude
around set value changes according to
controlled system. For reducing oscillation
period of temperature value, a threshold
zone is formed below or around set value
and this zone is named hysteresis.
Minimum Temperature Set Value Parameter ( Default = 10.0°C)
Temperature set value can not be lower than this value. This parameter value can be
adjusted from minimum value of device scale to maximum temperature set value
parameter
Maximum Temperature Set Value Parameter ( Default = 40.0 °C )
Temperature set value can not be greater than this value.
This parameter value can be adjusted from minimum temperature set value parameter
to maximum value of the device scale.
Temperature Sensor Offset Parameter ( Default = 0 )
From -10 to 10°C , NTC,PTC , PT-100 (0°C, 100°C)
From -18 to 18°F, NTC,PTC , PT-100 (32°F, 212°F)
From -10.0 to 10.0°C , NTC ,PTC , PT-100 (0.0°C,100.0°C)
From -18.0 to18.0°F NTC, PTC , PT-100 (32.0°F,212.0°F)
From -10 to 10°C ,ProNem Mini PMI-P ( -20°C, 80°C ),From -18 to 18°F,ProNem Mini
PMI-P ( -4°F, 176°F ),From -10.0 to 10.0°C, ProNem Mini PMI-P ( -20.0°C, 80.0°C ),
From -18.0 to18.0°F, ProNem Mini PMI-P ( -4.0°F,176.0°F )
Humidity Sensor Scale Selection Parameter ( Default = 0 )
Humidity input range is determined with this parameter.
0..10V
Z or
2..10V
Note :
parameter ProNem Mini PMI-
Hysteresis Parameter for Humidity ( Default = 1 )
From 1 to 10 for Humidity Sensor (0%RH, 100%RH)
From 0.1to 10.0 for Humidity Sensor (0.0%RH,100.0%RH)
In ON/OFF control algorithm,
value is tried to keep equal to set value by
opening or closing the last control element.
ON/OFF controlled system, temperature
value oscillates continuously. Temperature
value's oscillation period or amplitude
around set value changes according to
controlled system. For reducing oscillation
period of temperature value, a threshold
zone is formed below or around set value
and this zone is named hysteresis.
i
(1)
It is valid, if the device type 0/2...10V
(2) It is valid, if the device type 0/4...20mA
(1) (2)
Z or Z
0..20mA
(1) (2)
Z
4..20mA
Humidity
Temperature
thSt
Set
Control
Output
ON
OFF
P type device are not observed.
Humidity
hhSt
Set
Control
Output
ON
OFF
Z Humidity Sensor Input.
Z Humidity Sensor Input
thSt
Time
Time
hhSt
Time
Time
.
10