Break-In Procedure; Operation; Fuel Mixture; Mixing Fuel - Little Wonder 2230S Manual Del Operador Y De Piezas

LITTLE
WONDER
TRImmER
If the engine needs to be reinstalled:
1. Install the engine by first aligning the hex drive on the
trimmer gear housing with the single sided hex socket in
the engine.
2. Slide the engine over the 1" diameter stem containing
the hex drive on the gear housing until it is seated all
the way down on the gear housing. Tighten the 7/8"
Phillips Pan Head Screw (Pg. 17, Key #22).
3. Press shock absorbers into sockets on the gear hous-
ing followed by the spacer tubes. Secure the handle
and tubing support channel, spacer, and bracket with
the 1/4-20 hex bolts and locking nuts supplied.
4. With the stop switch in the stop position, and the
engine not running, check the throttle for proper op-
eration. Grasp rear handle with left hand, depressing
the lockout trigger until it stops when the carburetor
lever hits the carburetor case. Release the throttle
trigger and make sure the throttle returns to the
idle position, when the carburetor level rests on the
idle screw. Throttle movement should be smooth
and unobstructed.

BREAk-IN PROCEdURE

There are no special requirements for engine break-in.
After normal operation and two (2) tanks of fuel, engine
break-in is complete.
If adjustments are necessary, follow Special Car bu re-
tor Adjustment Procedures on this sup ple men ta ry Op-
erator's Information Sheet. All other adjustments and
maintenance procedures are in the complete Owner's
Manual.

OPERATION

The operator of this hedge trimmer is responsi-
ble for accidents or hazards occurring to himself,
other people or their property.
Fuel is extremely flammable. Handle it with care.
Keep away from ignition sources. Do not smoke
while fueling your equipment.

FUEL MIXTURE

Your Little Wonder Single Edge Hedge Trimmer is
®
powered by an Echo Model SV-5H/2. This model has
®
a two stroke, air cooled engine which requires a fuel
mixture of gasoline and 2-stroke oil.
1. Important Engine Information
This unit is certified to operate on approved two-stroke
fuel (a mixture of 2-stroke oil and gas o line/gasohol).
2. Fuel Statement
Gasoline - Use 89 Octane [R+M/2] gasoline or gasohol
known to be good quality. Gasohol may contain up to
10% Ethanol (grain alcohol) or 15% MTBE (methyl
tertiary-butyl ether). Gasohol con tain ing meth a nol (wood
alcohol) is NOT approved.
3. Two-Stroke Oil
A two-stroke engine oil meeting proposed ISO-L-EGD
Standard (ISO/CD 13738), must be used. LW brand
Premium 50:1 oil meets this proposed standard. Engine
problems due to in ad e quate lubrication caused by failure
to use an ISO-L-EGD approved oil, such as LW Premium
50:1 Two-stroke Oil, will void the two-stroke engine
warranty. (Emission related parts only are covered for
two years, regardless of two-stroke oil used, per the
statement listed in the EPA Phase I/California Emission
Defect Warranty Explanation.)

MIXING FUEL

1. Pour 1/2 of the gasoline into a safe container.
dO NOT mix fuel in the engine fuel tank.
2. Add the oil to the gasoline and mix.
3. Add the remaining gasoline and remix.
4. Install fuel cap and wipe spilled fuel from container
and area.
5. Important, two-stroke fuel separates and ages. Do
not mix more than you will use in a month. Shake fuel
container to thoroughly mix fuel before each use. Do
not attempt to run your engine on gasoline only, use
the proper fuel mixture.

STARTING A COLd ENGINE

The trimmer has a Start/Stop ignition switch which must
be used for starting and stopping the engine.
1. Place the hedge trimmer flat on the ground, or an-
other stable surface. Slide the ignition switch to the
START position.
OPERATION
9