Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Vehicle
Frame
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75529F
Wrenches: 18mm
Drill Bits: None
18mm crowfoot adaptor,
3/8" or 1/2" universal adaptor,
3/8" or 1/2" x 6" extension
2
1
Qty. (6)
12mm-1.75 X 35mm Cl 10.9 Hex head bolts
1
1.
Open vehicle back hatch door and open compartment in floor to access spare tire lowering screw. Use 19mm socket to turn
screw counter-clockwise and lower spare tire to allow easier access for installing bumper bolts.
2.
It may be necessary to temporarily lower exhaust system to allow for easier access to install frame bolts. If necessary remove
(2) rearward rubber isolator hangers per side. Spraying with a lubricant will aid in removing isolators off of studs.
3.
Raise hitch into position as shown above. Locate bumper bracket above vehicle fascia first before raising. It may be necessary
to pull down on bumper fascia slightly to get bracket in place.
4.
Install 12mm bolts and conical washers supplied as shown above.
5.
Use crowfoot adaptor and extension to torque 12mm bolts in bumper. Access from in front of hitch between spare tire.
6.
Reinstall exhaust hangers if removed. Raise spare tire back into position. Torque all fasteners to specifications below.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2007 Cequent Towing Products
Installation
Fascia
Bumper
2
Tighten all 12mm fasteners with torque wrench to 92 lb.-ft., 125 N*M
Instructions
Suzuki XL7
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1 & SUV2
1
Qty. (6)
2
Sheet 1 of 3
Manufacturer's Rating or
Max Gross
Trailer WT
4000lb. (1816 Kg)
4000 lb. (1816 Kg)
1/2" Conical washers
75529N
4-12-07
Form: F205 Rev A 5-6-05
Part Numbers:
75529
87436
44570
Max Tongue
WT
400 lb. (182 Kg)
400 lb. (182 Kg)
2
1
Rev. A
Publicidad
Manuales relacionados para Cequent Towing Products 75529
Resumen de contenidos para Cequent Towing Products 75529
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75529N 4-12-07 Rev. A 2007 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75529N 4-12-07 Rev. A 2007 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 75529N 4-12-07 Rev. A 2007 Cequent Towing Products Form: F205 Rev A 5-6-05...