Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: F75082
Wrenches: 18mm, 19mm, 7/8"
Drill Bits: ½"
43
43
43
43
97 and Prior Models
Note: 19mm open end style wrench
must be purchased to allow
removal of spare tire after
hitch installation.
1 1 1 1
Qty. (4)
Carriage Bolt ½-13 x 1-3/4"
2 2 2 2
Qty. (4)
Block ¼" x 1" x 2"
3 3 3 3
Qty. (4)
Lock Washer ½"
1.
For vehicles with step bumper, remove rearmost bumper bracket bolt and J-nut (both sides).
2.
Position hitch on vehicle, sandwiching bumper brackets (if present) between hitch and vehicle frame. Install rearmost fasteners.
3.
Using hitch as a template, drill (2) ½" holes into frame at forward end of hitch.
Note: On some models, holes may already exist.
4.
Install remaining fasteners as shown. For vehicles with step bumper, place 3/16 x 1 x 2 block (Item 5) between frame and side
brackets at forward attachment as shown.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2002, 2006 Cequent Towing Products
Installation Instructions
Ford Ranger, Mazda B2300,
Mazda B3000, Mazda B4000
Note: Relocation of spare tire bracket is NOT required.
Bumper
Place between frame and hitch
if vehicle is equipped with step
bumper
Frame Rail
34
34
34
34
Tighten all ½" GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3
5 5 5 5
43
43
43
43
Bumper
Bracket
4 4 4 4
Qty. (4)
Hex Nut – ½-13
5 5 5 5
Qty. (2)
Block 3/16" x 1" x 2"
Sheet 1 of 3
N75082
Part Numbers:
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
6000 (2 724 Kg)
750 (340.5 Kg)
4000 (1 816 Kg)
12
12
12
12
Frame rail
Bumper
Bracket
Existing Bumper
Bracket Fasteners
Rearmost to be Removed
34
34
34
34
11/21/07
Form: F205 Rev A 5-6-05
75082
33058
78165
87161
Max Tongue
WT (LB)
400 (182 Kg)
Rev. B

Publicidad

loading

Resumen de contenidos para Cequent Towing Products 75082

  • Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 N75082 11/21/07 Rev. B 2002, 2006 Cequent Towing Products Form: F205 Rev A 5-6-05...
  • Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 N75082 11/21/07 Rev. B 2002, 2006 Cequent Towing Products Form: F205 Rev A 5-6-05...
  • Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 N75082 11/21/07 Rev. B 2002, 2006 Cequent Towing Products Form: F205 Rev A 5-6-05...

Este manual también es adecuado para:

330587816587161