Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame Structure
Spare Tire
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75401F or 87407F
Wrenches: 11/16, 3/4
Drill Bits: None
Fasteners Typical Both Sides
1
Qty. (2)
3/8-16 X 1.25 GR5 Carriage Bolt
2
Qty. (2)
3/8 Conical Toothed Washer
3
Qty. (2)
3/8 Hex Nut
4
Qty. (2)
½-13 X 2.00 GR5 Carriage Bolt
1.
Lower the spare tire from the underside of the vehicle.
2.
Remove the two (2) plastic fascia tabs (do not discard).
3.
Using the 3/8 wire pull, insert the 3/8 Carriage bolts through the end of the inside portion of the vehicle bumper structure and
through the existing slots.
4.
Raise hitch into position and loosely install 3/8 Conical toothed washers and 3/8 Hex nuts as shown above.
5.
Using the ½ wire pull insert the ½ Carriage bolts and ¼ X 1.00 X 3.00 Blocks through the vertical holes in the vehicle frame
structure to the existing holes in the vehicle frame rails and through the receiver.
6.
Install ½ Conical toothed washers and ½ hex nuts.
7.
Tighten all fasteners to the required torque specifications.
8.
Reinstall the two (2) plastic fascia tabs removed in installation step 2.
9.
Raise spare tire back into position.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005, 2006 Cequent Towing Products
Installation Instructions
Subaru B9 Tribeca
Bumper Structure
Fascia
Tighten all 3/8-16 GR5 fasteners with torque wrench to 30 Lb.-Ft.
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft.
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2
Frame Structure
5
Qty. (2)
¼ X 1.00 X 3.00 Block
6
Qty. (2)
½ Conical Toothed Washer
7
Qty. (2)
½ Hex Nut
Sheet 1 of 3
75401N
Part Numbers:
75401
44535
87407
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
4000
400
3500
350
Bumper Structure
01-24-06
Rev. B
Publicidad
Manuales relacionados para Cequent Towing Products 75401
Resumen de contenidos para Cequent Towing Products 75401
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75401N 01-24-06 Rev. B 2005, 2006 Cequent Towing Products...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75401N 01-24-06 Rev. B 2005, 2006 Cequent Towing Products...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 75401N 01-24-06 Rev. B 2005, 2006 Cequent Towing Products...