Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Exhaust
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: F75193
Wrenches: 5/8, 3/4, Torque wrench
Drill Bits: NONE
Hitch requires 5/8" pin & clip
Existing Access
Hole
5
6
7
1
Qty. (2)
Hex Bolt - M12 x 1.75 x 40mm CL 8.8
2
Qty. (2)
Conical Toothed Washer 1/2
3
Qty. (2)
Hex Bolt - 7/16-14 x 1.50 Gr5
4
Qty. (2)
Conical Toothed Washer 7/16
1.
Remove existing bolt from frame/bumper attachment (one from each side of vehicle).
2.
If equipped, remove tow hooks and return to customer.
3.
Raise hitch into position as shown. Replace bolt removed in step one with 7/16-14 x 1-1/2" bolts or M12 x 1.75 x 40mm
bolts as shown. Bolts required vary by vehicle. Install remaining fasteners as shown.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
,
2002
2007 Cequent Towing Products
Installation Instructions
JEEP WRANGLER
Bumper
Frame
Existing Weldnut
3
4
Tighten all 7/16 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Tighten all ½ GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Tighten all M12 CL 8.8 fasteners with torque wrench to 68 Lb.-Ft. (91 N*M)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV 5, SUV 7
Varies by Vehicle
1
2
5
Qty. (2)
Hex Bolt - ½-13 x 1.75 Gr5
6
Qty. (2)
Lock washer 1/2
7
Qty. (2)
Handle Nut assembly ½-13
N75193
Part Numbers:
75193
87431
44565
33036
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
N/A
N/A
4000 (1814 Kg)
400 (181 Kg)
Fasteners Typical
Both Sides
1-15-07
Rev. B
Form: F205 Rev A 5-6-05
Publicidad
Manuales relacionados para Cequent Towing Products 75193
Resumen de contenidos para Cequent Towing Products 75193
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 N75193 1-15-07 Rev. B 2002 2007 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Página 2 Ne jamais utiliser une torche pour découper un accès ou un trou de fixation. Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 N75193 1-15-07 Rev. B 2002 2007 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 de 3 N75193 1-15-07 Rev. B 2002 2007 Cequent Towing Products Form: F205 Rev A 5-6-05...