While Operating - Troy-Bilt TBTP Manual Del Operador

• Inspect all extension cords and the unit power
connection periodically. Look closely for deterioration,
cuts or cracks in the insulation. Also inspect the
connections for damage. Replace the cords if any
defects or damage appear.
• Prevent disconnection of the tree pruner powerhead
from extension cord during operation by using a plug-
receptacle retaining strap, connector, or by making a
knot as shown below:
Extension Tree Pruner
Cord
Cord
• Avoid dangerous environments. Never operate your unit
in damp or wet conditions. Moisture is a shock hazard.
• Do not use the unit in the rain. Do not use in or around water.
• Do not handle the plug or unit with wet hands or
standing on any wet surfaces.
• Keep pruner away from power lines or electrical wires.
• Do not leave the unit plugged in when not in use, changing
attachments or add-ons, or while being serviced.

WHILE OPERATING

• Wear safety glasses or goggles that are marked as
meeting ANSI Z87.1 standards, and ear/hearing
protection when operating this unit. Wear a face or
dust mask if the operation is dusty.
• Wear heavy, long pants, boots, gloves and a long
sleeve shirt. Do not wear loose clothing, jewelry, short
pants, sandals or go barefoot. Secure hair above
shoulder level.
• Use the unit only in daylight or good artificial light.
• Do not force unit. It will do the job better and with less
likelihood of injury at a rate for which it was designed.
• To reduce the risk of electrical shock, keep the pruner
from power lines or electrical wires.
• Use the right tool. Use this unit only as described in
this manual. Do not use for any job except that for
which is intended.
• Do not overreach. Always keep proper footing and
balance.
• Always hold the unit with both hands when operating.
Keep a firm grip on both the front and rear handle or
grips.
• A coasting blade can cause injury while it continues
to moves after the unit is stopped. Maintain proper
control of the unit until the blade has completely
stopped moving.
• Keep hands, face, and feet at a distance from all
moving parts. Do not attempt to touch or stop the
blade when it is moving.
4
RULES FOR SAFE OPERATION
Extension Tree Pruner
Cord Cord
• Do not operate the unit faster than the speed
needed to prune. Do not run the unit at high speed
when not pruning.
• Always stop the unit when work is delayed or when
walking from one cutting location to another.
• If you strike or become entangled with a foreign object,
stop the engine immediately and check for damage.
Have any damage repaired before attempting further
operations. Do not operate unit with a bent, cracked or
dull blade. Discard blades that are bent, warped,
cracked or broken.
• Stop the unit IMMEDIATELY if you feel excessive
vibration. Vibration is a sign of trouble. Inspect
thoroughly for loose nuts, bolts or damage before
continuing. Repair or replace affected parts as
necessary.
• Stop and switch the unit to off for maintenance,
repair, or for changing add-ons attachments.
• Use only Genuine Factory Parts™ and accessories for
this unit. These are available from your authorized
service dealer. Use of any Genuine Factory Parts™ or
accessories could lead to serious injury to the user or
damage to the unit, and void your warranty.
OTHER SAFETY WARNINGS
• Allow the unit to cool before storing or transporting. Be
sure to secure the unit while transporting.
• Store the unit inside in a dry place, either locked up or
up high to prevent unauthorized use or damage. Keep
out of the reach of children.
• Never douse or squirt the unit with water or any other
liquid. Keep handles dry, clean and free from debris.
Clean after each use, see Cleaning and Storage
instructions.
• Keep these instructions. Refer to them often and use
them to instruct other users. If you loan someone this
unit, also loan them these instructions.
• Only qualified personnel should perform any repairs
or maintenance procedures that are not described
in this manual.
• Check shear bolts, engine mounting bolts and other
bolts at frequent intervals for proper tightness to be
sure the equipment is in safe working condition.
• Always refer to the Operator's Manual instructions for
important details if the unit is to be stored for an
extended period.
• Do not attempt to repair the machine unless you have
the proper tools, and instructions for disassembly and
repair of the machine.
SAVE THESE INSTRUCTIONS