Ribind MASTER Wi-Fi Instrucciones De Instalación página 20

G
B
E -
MASTER Wi-Fi OS POWER
After having made all of the connections, provide power to the control panel.
The yellow LED DL6 should turn on and the buzzer will emit a sound indicating correct power.
F -
IDENTIFICATION OF SAFETY DEVICES
ATTENTION: BEFORE THE SAFETY STRIPS IDENTIFICATION, CHECK IF THE CONTROL
BOARD IS DESIGNED FOR ONE OR TWO INPUTS FOR SAFETY STRIPS CONNECTING.
RUN THE JUMPER JP2 SETTING ACCORDING TO THE NUMBER OF INPUTS FOR
SAFETY STRIPS CONNECTING (Pic. 1).
JP2 LEFT
FOR CONTROL PANEL WITH 2 INPUTS
FOR THE DIFFERENT MANAGEMENT OF
THE SAFETY STRIPS IN OPENING AND
CLOSING
3 safety edges can be assigned for each
of the 2 control panel inputs.
EDGE 1 = yellow wire - safety edge in
opening DIP 1-3 (LED EDGE PHOT from 1
to 3),
EDGE 2 = green wire - safety edge in closing
DIP 4-6 (LED EDGE PHOT from 4 to 6)
Every Wi-Fi safety device must OBLIGATORILY be identified placing only one of the 6 DIPs
present on its circuit (different for each of the 6 safety devices) in the ON position. Obviously
one pair of photocells is considered one safety device and must therefore have infrared ray
receiver and transmitter with the same DIP in the ON position.
ATTACH THE YELLOW NUMBERED STICKER TO EACH SAFETY DEVICE COVER TO
IDENTIFY IT WITH THE NUMBER OF THE DIP TURNED ON ON MASTER CARD.
The sticker is used to quickly identify the safety device which needs maintenance.
Note: Each safety device is supplied with the DIPs in OFF position so that battery power is
maintanined when not in use (if inserted).
Insert the batteries in the Wi-Fi safety devices.
G -
MEMORIZATION OF THE SAFETY DEVICES
After having attached the yellow numbered stickers to the safety devices covers, and
having inserted the batteries, on MASTER place the DIPs with the same numbers in the
ON position.
Use the following procedure for memorization:
- Push the button PROG RX on the MASTER Wi-Fi OS => LED EDGE PHOT 1 flashes red
for 1 minute (the time provided for memorization).
- Push the button PROG TX on the safety device with DIP 1 in ON position => LED
EDGE PHOT 1 since red, turns green and a sound from the buzzer indicates that the safety
device has been memorized correctly. Immediately LED EDGE PHOT 2 begins flashing red.
- If there are no other safety devices to be memorized after one minute the dual-color
LED EDGE PHOT 2 will turn off or, push the button PROG. RX 4 times to end the
memorization procedure => all of the LED EDGE PHOT must be off.
MEMORIZATION OF OTHER SAFETY DEVICES
- After having memorized the first safety device, LED EDGE PHOT 2 automatically begins
flashing red for 1 minute (the time provided for memorization).
12/24V ac/dc
JP2 RIGHT
FOR CONTROL PANEL WITH 1 INPUT
FOR THE MANAGEMENT OF THE SAFETY
STRIPS
EDGE 1 = yellow wire - safety edge in
opening and closing (LED EDGE PHOT
available from 1 to 6)
- Push the button PROG. TX on the safety device with DIP 2 in ON position => LED
EDGE PHOT 2 flashing red, turns green and a sound from the buzzer indicates that the
safety device has been memorized correctly.
- Follow the same procedure for any other safety devices (up to a maximum of 6).
ADDING OTHER SAFETY DEVICES (UP TO 6 TOTAL)
If after installation the use of further safety devices is desired to increase door safety, it is
recommended to:
- Turn off power to the door.
- Place the safety device in the desired position and identify it by moving the internal DIP.
- Identify it with the corresponding yellow numbered sticker (see paragraph F -
IDENTIFICATION OF Wi-Fi SAFETY DEVICES).
- Enable the DIP of the safety device just added to the MASTER Wi-Fi OS card.
- Return power to the door.
- Follow the memorization procedure and system check as indicated previously.
NOVA Wi-Fi AND VERTIGO Wi-Fi PHOTOCELLS - SYSTEM CHECK
- Check that DIP selected on the infrared ray transmitter TX NOVA Wi-Fi is the same as that
selected on the receiver RX NOVA Wi-Fi (ex: DIP 1 ON).
- Proper operation of TX NOVA Wi-Fi is shown by the green LED which turns on for 10
seconds.
- Push and release the button S3 "PROG. TX" on the NOVA Wi-Fi receiver (it turns on for
3 minutes to perform the alignment procedure). If the photocells are already aligned the
red LED emits a steady light. If the red LED is off or emits a flashing light, perform the
alignment until it emits a steady light.
- After the alignment, check it by placing an obstacle so that the red LED turns off and at
the same time the LED EDGE PHOT, paired with it, turns on green for the time that the
obstacle is present.
- On MASTER card, LED DL3 should also be off indicating a proper exchange of the contact
on PHOTO input of the control panel.
- Repeat the procedure to the other photocells.
- Perform a function check to all the photocells, activating the movement of the automation
and checking that by placing an obstacle the automation stops/reverses when closing, or
stops/continues to open when opening.
TOUCH Wi-Fi STRIP - SYSTEM CHECK
After having adjusted the TOUCH Wi-Fi strip correctly:
- Press the gummy of a TOUCH Wi-Fi strip (for example: safety strip with DIP 3 ON).
1 - LED EDGE PHOT 3 flashes green and LED DL2 momentarily turns off and then turns on.
ATTENTION: after receiving the first signal, other signals are ignored for 2 seconds. If there
is a signal in these 2 seconds it will be from the LED EDGE PHOT 3 which turns green.
- Repeat the LED activation check on the MASTER Wi-Fi OS pressing the other TOUCH Wi-Fi
strips installed.
- Perform a final check of all strips installed, activating the movement of the automation
and ensuring that upon impact with the strip the automation stops/reverses movement.
ANTENNA 868MHz
In order to communicate with 868 MHz Wi-Fi safety devices, MASTER Wi-Fi OS is equipped
with a piece of electric wire that acts as an antenna linked to the J8 terminal. If it is
necessary to improve the radio signal (for example, with MASTER Wi-Fi OS inserted in a
metallic box), connect the 868.3 MHz antenna (code ACG5451) to the J8 terminal, ensuring
the correct connection of the central and shield wires of the aerial cable, and position it in
such a way so that it is "in view" of all safety devices.
To get the system working properly it is necessary that between MASTER and
safety devices there are no obstacles such as reinforced cement walls, iron
surfaces, etc. that could block the radio signals.
NOVA Wi-Fi AND VERTIGO Wi-Fi PHOTOCELLS ALARM SIGNAL CHECK
Check that by taking the battery out of photocell receiver with DIP 3 ON (for example), and
commanding the door to open, the LED EDGE PHOT 3 flashes green/red, while LEDs DL1,
DL2 and DL3 turn off, and that buzzer emits tones for 1 minute.
Repeat the check for any other photocell receivers installed.
20
12/24V ac/dc