Publicidad
Idiomas disponibles
Idiomas disponibles
en
PRODUCTS COVERED BY THIS MANUAL
CE 50HZ NIGHT-LITE PRO II ®
IMPORTANT: This is the second of two setup instruction
manuals for this unit. Complete the setup in the first manual
(106831 or 106842) before performing the setup in this man-
ual.
WARNING
!
Do not attempt to start or operate this unit until all assembly steps
have been completed. Serious injury or equipment damage may
result.
JACK INSTALLATION
Parts List:
2 - 330008 Top Crank Jacks
1 - 650235 Side Crank Jack
3 - 330014 Jack Snap Rings
1. Locate the jack mounting plates on the outriggers at the two
corners of the tower (A, Figure 1). Ensure surfaces on both
the outriggers and the jacks (C, Figure 2) are clean and unob-
structed.
2. Mate the top crank jacks to the mounting plates and secure
with the snap rings (D, Figure 2). Ensure that the snap rings
are fully seated in the locating groove (B, Figure 1). See
Figure 3 for completed assembly.
3. Repeat for the side crank jack, installing it to the mounting
plate at the rear center of the tower (F, Figure 4).
FENDER INSTALLATION
Parts List:
2 - 650297 Rotation Molded Fenders
10 - 047010 5/16 Flat Washers
10 - 044031 5/16-18 Keps Hex Nuts
1. Using the fender mounting bolts located on the tower side
panels (A, Figure 5; installed), mount the fender (B) to the
tower. Install one flat washer (C) and one keps nut (D) on
each bolt. Tighten keps nuts.
NOTE: Some components in Figure 5 are removed for clarity.
2. Repeat for opposite side.
6
TOWER INSTALLATION
Parts List:
1 - Tower Assembly
3 - 044016 10-24 x ½ PHRH screws
3 - 041024 10-24 keps nuts
1 – 041075 5/16-18 x ¾ self tapping screw
1 – 101410 tower mount bracket
2 – 046110 3/8-16 x 1 bolts
2 – 046115 3/8-16 x 1 ¼ bolts
8 – 047010 5/16 flat washers
4 – 044036 3/8-16 keps nuts
!
NOTE: An overhead hoist is required for tower installation.
1. Mount eye bolts (A, Figure 6) in the center hole of the Nycoil
bracket (B) on both sides of the tower. Drop hoist chains
between the tower and the Nycoil (C) and attach to the eye
bolts.
2. Using the hoist, lift the tower (D, Figure 7) over the unit.
Slowly lower the tower into position making sure the tower
does not catch on the electrical cords inside the unit. Also
see Figures 8 and 9.
3. When fully lowered, the mounting flange on the front of the
tower (E, Figure 10) will mate to the flange (F) on the unit
stringer. The tower base (G, Figure 11) will rest in the mount-
ing bracket on the floor of the unit. The pin (not shown) in the
center of the base mounting bracket will locate the base of
the tower.
4. Install the tower mount bracket (H, Figure 12) with flat wash-
ers and 3/8-16 x 1-1/4 bolts (I, Figure 13) on the horizontal
surface, and 3/8-16 x 1 bolts on the vertical surface (J). Install
flat washers and keps nuts on all the bolts.
5. Tighten the square headed set bolts (K, Figure 14) at the
base of the tower.
6. Install the 5/16-18 x ¾ self tapping screw (L, Figure 15) in the
flange on the pump bracket. Also, ensure the mounting bolts
(M, Figure 16) on top of the pump bracket are tight.
7. Connect the hose from the hydraulic pump (N, Figure 17)
to the Quick Disconnect nipple at the base of the hydraulic
cylinder (O).
8. Route the power cord from the tower lights (P, Figure 18)
through opening beside the hydraulic cylinder. Route the
electric cord up through the bottom of the control box (Figure
19) using the open cord grip. Pull the cord into the control box
until the stripped edge of the cord is about 25mm from the
top of the box. Using the wiring schematic 106337 attach the
wires using the ground bolt and the supplied wire locks.
9. Close both sides of the control box. Secure the face plates
using 3 10-24 x ½ pan head screws and 10-24 keps nuts.
See Figure 20.
Publicidad
