Tabla de contenido
Publicidad
P O R T E R O
VERIFICACIÓN DE LA INSTALACIÓN
No funciona nada
No se iluminan los tarjeteros
No se ilumina el piloto del pulsador de iluminación.
No se oye ningún teléfono desde la placa de calle.
No se oye un teléfono desde la placa de calle.
No se oye la placa de calle en ningún teléfono.
OPERATING PROBLEMS
If there is a fault, connect up a single telephone to terminals
1, 2, 3, 4 and to a push button on the entrance panel where
the anomaly is. In this way, you will be able to check whether
the problem is in the entrance panel or in the telephone
connections.
Nothing works.
Check the mains voltage in the power supply. Check that the
voltage between
and V
Check whether there are any short circuits and fix them.
Disconnect the power supply for 1 minute and then connect it
up again. If it still doesn’t work, disconnect all the power supply
V and
terminals, and check that the voltage between
and V
is 12 Vac. If this is not the case then there may be
something wrong with the power supply.
The card holders do not light up.
Check that the voltage between
is 12 Vac. Check that the voltage between 9 and 10 in the
audio unit, with the lighting push button activated, is 12 Vac.
Check whether the lamp is burnt out.
The lighting push button pilot does not light up.
Check that the voltage between
12 Vac. If the voltage is correct, there may be something wrong
with the audio unit.
You cannot hear any telephones from the entrance panel.
Check connections 2 and 3 from the audio unit to all the
telephones. Check the volume control on the panel and the
E L E C T R Ó N I C O
-
D O O R
of the power supply is 12 Vac.
and V of the power supply
and V in the audio unit is
E N T R Y
S Y S T E M S
-
No se oye la placa de calle en un teléfono.
Se oye un pitido en la placa. El sonido se acopla.
No suena la llamada en ningún teléfono.
No suena la llamada en un teléfono.
No se oye la confirmación de llamada en la placa de calle.
No funciona el abrepuertas.
lighting push button pilot. If you cannot find the fault, there may
be something wrong with the audio unit.
You cannot hear a telephone from the entrance panel.
Check connections 2 and 3 from the audio unit to the telephone.
If you cannot find the fault, there may be something wrong with
the telephone.
You cannot hear the entrance panel on any telephone.
Check connections 2 and 4 from the audio unit to all the
telephones. Check the volume control on the telephones (on the
panel) and the lighting push button pilot. If you cannot find the
fault, there may be something wrong with the audio unit.
You cannot hear the entrance panel on a telephone.
Check connections 2 and 4 from the audio unit to the telephone.
If you cannot find the fault, there may be something wrong with
the telephone.
You can hear whistling in the panel. The sound produces
feedback.
Lower the sound level using the volume control on the audio
unit.
The call tone doesn’t ring on any telephone.
For electronic call, check that the voltage between 2 and 7, is
9 Vdc in the audio unit, without pressing the push button. For
buzzer call, check that the voltage between 2 and 8, is 12 Vac
in the audio unit, without pressing the push button. Check the
connection between 7 (electronic call) or 8 (buzzer call) in the
audio unit and the push buttons. Check connection 2 from the
audio unit to the telephones. If you cannot find the fault, there
may be something wrong with the audio unit.
P O R T I E R
É L E C T R O N I Q U E
Publicidad
Tabla de contenido
