Description, Specifications And Standard Equipment Description; Specifications; Standard Equipment - RIDGID K-1500A Manual De Instrucciones

Description, Specifications and

Standard Equipment

Description
The RIDGID ® K-1500A/B & K-1500SP Drain Cleaning
Machines are for cleaning 2" through 10" lines. These ma-
chines are driven by induction motors that have a grounded
electrical system. An integral Ground Fault Interrupter
(GFCI) is built into the line cord. A toggle or rotary switch pro-
vides FORWARD/OFF/REVERSE control of the motor.
Machines are designed to use sectional-type cable that
has a quick coupling system for disconnecting tools. The
cable is manually fed in and out of the machine and rotates
at a cable speed of 600 to 700 RPM. The rotation of the
cable is controlled by a clutch handle. The cable stops in-
stantly when the clutch handle is released.
K-1500 machines come equipped to run 1
clean 3" – 10" lines through 200' – the 1500SP through
300'. They can be easily adapted to use 7/8" cable to clean
2" – 4" lines.

Specifications

Line Capacity ...............Depends on choice of cable.
Refer to the following chart for
recommendations.
Motor
K-1500A/B
Type ............................115V/60Hz, Reversible, 230V-
240V/50Hz Versions Available
Upon Request
Rating .......................... 3 /
Amps ...........................10.4
K-1500A/B-SP
Type ............................115V/240V/50-60Hz,
Reversible,Total Enclosed Fan
Cooled
Rating ..........................1 HP
Amps ...........................15
Sound Pressure (L )* ......68.4 dB(A), K=3
PA
Sound Power (L )*...........77 dB(A), K=3
WA
* Sound measurements are measured in accordance with a standardized test per
Standard EN 62841-1.
Chart 1
Model Frame
No. Style
K-1500A
A
K-1500A-SE
K-1500B
B
K-1500B-SE
K-1500SP B
K-1500SPA A
278-104-421.10_REV. A
1 / " cable to
4
HP
4
Cable Capacity
Size
Line Reach
7 / " 2" - 4"
8
or
1 1 / " 3" - 10"
4
7 / " 2" - 4"
8
1 1 / " 3" - 10"
4
K-1500A/B, & K-1500SP Drain Cleaning Machines
- Sound emissions may vary due to your location and specific use of these tools.
- Daily exposure levels for sound need to be evaluated for each application and ap-
propriate safety measures taken when needed. Evaluation of exposure levels
should consider the time a tool is switched off and not in use. This may signifi-
cantly reduce the exposure level over the total working period.
K-1500A/B-SP
A Style .........................2 Wheels In Rear w/Upright
B Style .........................2 Wheels In Front On
See the RIDGID Catalog for machine model options and
accessories. Every machine model includes as standard
equipment:
Standard Equipment
• A-1 Operator's Mitt
• A-12 Pin Key
• A-34-12 Rear Guide Hose
Clutch
Handle
Tool
Figure 1 – K-1500A and K-1500SPA Drain Cleaners
Horsepower
175'
3 / HP at 710 RPM
4
200'
175' 1HP at 600 RPM
300'
Handle On Frame Assembly
and Cable Storage Capacity
FrameAssembly.
Guide
Hose
FOR/OFF/REV
Switch
Overall
Height Width Length Wt. Lbs.
41 1 / " 20 3 / " 16"
2 4
27 3 / " 20 3 / " 40 5 / "
4 4 8
27 3 / " 20 3 / " 40 5 / "
4 4 8
41 1 / " 20 3 / " 16"
2 4
Machine
92
80
110
138
5