DrBrowns AC178-INTL Instrucciones De Uso página 9

REPLACING HEPA FILTER:
For optimal performance, it is recommended to replace the filter every 6 months of
regular use. Replace the filter by following the steps below.
1. Remove the filter cover from the bottom of the base and take out the old filter.
2. Place a new filter into the base, ensuring the pull tab is still visible on top of the filter.
3. Insert the filter cover back into the base.
NOTE: Filter must always be used to ensure proper performance.
4
D
C
B
A
To purchase replacement filters, contact your local distributor.
4
WARRANTY:
This appliance is warranted against defective material or workmanship for a period of
one year from the date of purchase. Any defective part will be repaired or replaced at
no charge if it has not been tampered with and the appliance has been used according
to these printed instructions. This warranty gives you specific legal rights as well as
other rights that vary from state to state.
This warranty does not cover a defect that has been caused by negligence,
accidents or improper use of the appliance. To keep your Dr. Brown's
Sterilizer and Dryer in good condition and retain your warranty, USE ONLY AS
DIRECTED.
CUSTOMER SERVICE
If you experience unsatisfactory operation or have questions/comments, please contact
your local Dr. Brown's distributor. See drbrownsbaby.com to find your local contact.
3 2
B
A
DESIGN UNITS: MILLIMETERS
TOLERANCES UNLESS NOTED:
NO PLACE: X
ONE PLACE: .X
TWO PLACE: .XX
THREE PLACE: .XXX
ANGLE: X
2 HEPA Type Filters are included.
ANGLE: .X
THIRD ANGLE
PROJECTION
3 2
2
1
THIS DRAWING AND RELATED 3D CAD DATA
HANDI-CRAFT COMPANY
CONTAINS PROPRIETARY INFORMATION THAT
ARE THE PROPERTY OF
2.5
HANDI-CRAFT CO. AND ARE NOT TO BE
0.5
4433 FLYER AVE. ST. LOUIS MO. 63116, USA
COPIED OR USED WITHOUT THE PERMISSION
0.25
OF HANDI-CRAFT CO.
0.13
0.5
INTERPET PER ASME Y14.5-1994 DRAWN
RBW
0.25
OTHER HANDI-CRAFT ENGINEERING
STANDARDS MAY APPLY ENG APPR.
SOLIDWORKS 3D
MFG/Q.A APPR.
2
DESIGN UNITS: MILLIMETERS DRAWN RBW 15JUL19
HANDI-CRAFT COMPANY
TOLERANCES UNLESS NOTED:
ENG APPR.
NO PLACE: X 2.5
4433 FLYER AVE. ST. LOUIS MO. 63116, USA
ONE PLACE: .X 0.5 MFG/Q.A APPR.
TWO PLACE: .XX 0.25
TITLE:
THIS DRAWING AND RELATED 3D CAD DATA
THREE PLACE: .XXX 0.13
FILTER REPLACEMENT
CONTAINS PROPRIETARY INFORMATION
ANGLE: X 0.5
THAT ARE THE PROPERTY OF
ANGLE: .X 0.25
HANDI-CRAFT CO. AND ARE NOT TO BE
COPIED OR USED WITHOUT THE
PERMISSION OF HANDI-CRAFT CO.
DO NOT SCALE DRAWING
SIZE C DWG. NO.
INTERPET PER ASME Y14.5-1994
THIRD ANGLE OTHER HANDI-CRAFT ENGINEERING
PROJECTION STANDARDS MAY APPLY
MATERIAL
SOLIDWORKS 3D SCALE: 1:1 SHEET 1 OF 1
1
D
C
B
TITLE:
SIZE
A
MATERIAL
15JUL19
SCALE: 1:2
DO NOT SCALE DRAWING
A
REV. 1
Bottle
TM
1
B
A
FILTER AND COVER
DWG. NO. REV.
1
SHEET 1 OF 1
1
8