General Power Tool Safety Warnings - Makita DSS500 Manual De Instrucciones

ENGLISH (Original instructions)
1. Red indicator
2. Button
3. Battery cartridge
4. Star marking
5. Lever
6. Base
7. Cutting line
8. Lock-off lever
SPECIFICATIONS
Model
Blade diameter
Max. Cutting depth
No load speed (min
Overall length
Net weight
Rated voltage
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use
The tool is intended for performing lengthways and
crossways straight cuts and mitre cuts with angles in
wood while in firm contact with the workpiece.
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
CORDLESS CIRCULAR SAW
SAFETY WARNINGS
Cutting procedures
1. DANGER: Keep hands away from cutting area
and the blade. Keep your second hand on
auxiliary handle, or motor housing. If both hands
are holding the saw, they cannot be cut by the blade.
2. Do not reach underneath the workpiece. The guard
cannot protect you from the blade below the
workpiece.
3. Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
4. Never hold piece being cut in your hands or
across your leg. Secure the workpiece to a stable
6
All manuals and user guides at all-guides.com
Explanation of general view
9. Switch trigger
10. Shaft lock
11. Hex wrench
12. Hex bolt
13. Outer flange
14. Saw blade
15. Inner flange
16. Dust nozzle
at 90°
at 45°
-1
)
ENE028-1
GEA010-1
GEB061-4
17. Screw
18. Hose
19. Vacuum cleaner
20. Adjusting screw for 90°
21. Triangular rule
22. Limit mark
23. Brush holder cap
24. Screwdriver
DSS500
136 mm
51 mm
35 mm
3,600
359 mm
2.6 kg
D.C. 14.4V
platform. It is important to support the work properly
to minimize body exposure, blade binding, or loss of
control.
A typical illustration of proper hand support and
workpiece support. (Fig. 1)
5. Hold the power tool by insulated gripping surfaces
only, when performing an operation where the
cutting tool may contact hidden wiring. Contact
with a "live" wire will also make exposed metal parts of
the power tool "live" and could give the operator an
electric shock.
6. When ripping, always use a rip fence or straight
edge guide. This improves the accuracy of cut and
reduces the chance of blade binding.
7. Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades
that do not match the mounting hardware of the saw
will run eccentrically, causing loss of control.
8. Never use damaged or incorrect blade washers or
bolt. The blade washers and bolt were specially
designed for your saw, for optimum performance and
safety of operation.
Kickback causes and related warnings
- kickback is a sudden reaction to a pinched, bound or
misaligned saw blade, causing an uncontrolled saw to
lift up and out of the workpiece toward the operator;
- when the blade is pinched or bound tightly by the kerf
closing down, the blade stalls and the motor reaction
drives the unit rapidly back toward the operator;
- if the blade becomes twisted or misaligned in the cut,
the teeth at the back edge of the blade can dig into the
top surface of the wood causing the blade to climb out
of the kerf and jump back toward the operator.
DSS501
364 mm
2.7 kg
D.C. 18V