Handle Assembly; Grass Catcher Assembly; Safety Key (Deactivation Device); Cutting Height Adjustment - ST CP1 430 Li 48 Serie Manual De Instrucciones

4. Dispose of the box and packaging in compliance with
local regulations.
Before assembling, make sure the safety key is not
inserted into its housing.
4.2

HANDLE ASSEMBLY

Assemble the handle according to the indications in (Fig.4),
(Fig.5), (Fig.6).
4.3

GRASS CATCHER ASSEMBLY

Assembly the grass catcher as illustrated in (Fig.7).
5. CONTROLS
5.1

SAFETY KEY (DEACTIVATION DEVICE)

The key (Fig.8.A) found inside the battery compartment en-
ables / disables the machine's electrical circuit.
Removing the key, the electric circuit is completely deacti-
vated to prevent uncontrolled use of the machine.
IMPORTANT Remove the safety key whenever the ma-
chine is unused or left unattended.
For certain models, if required, turn the key to "ON"
position to activate the electric circuit of the machine to
activate its start-up.
Turning the key to "OFF", the electric circuit of the ma-
chine is completely deactivated, to prevent any uncon-
trolled use of the machine.
5.2 HANDLE
5.2.1 Operator presence lever
The operator presence lever (Fig.9.A) enables the cutting
means.
It is located in front of the handle.
Press the safety button (Fig.9.C) and bring the lever to-
wards the handle in order to start the cutting means.
When the lever is released, the motor automatically stops
and all functions are disabled.
NOTE The cutting means engagement is possible only
by pressing the yellow button on the right side of the han-
dle and bringing the operator presence lever towards the
handle.
5.2.2 Power button
The power button (Fig.12.A) is used to:
Machine start-up. By pressing the button
1.
(Fig.10.A) the LED (Fig.10.B) switches on and
the machine is ready for use.
NOTE The machine can be switched on
only if the operator presence lever and the
drive lever are released.
NOTE In case the machine is not oper-
ated, the LED switches off after 15 seconds
and the above-mentioned operation must be
carried out again.
Cutting means engagement.
2.
NOTE The cutting means engagement is
possible only by pressing the operator pres-
ence lever on the handle (see par. 6.3).
Cutting means disengagement. With the
3.
cutting means engaged, release the operator
presence lever (Fig.10.A); the cutting means
stops whilst keeping the machine powered on.
5.2.3 Drive ON lever
IMPORTANT The engine has to be always started
with the drive disengaged.
This engages the wheel drive and allows the machine to
move forward.
It is located behind the handle.
Drive engaged. The lawn mower is driven
forward with the lever pulled against the
handle (Fig.9.A). The lawn mower stops
moving forward when the lever is released.
IMPORTANT Avoid moving the machine backwards
when the drive is ON.
For certain models, the forward speed can be adjusted
with the selection knob located on the right side of the
handle (Fig.10.C).
You can select 6 different levels of speed.
1. Maximum speed (about 5 Km/h).
2. Minimum speed (about 2.5 Km/h).
NOTE The last speed level selected remains set even
after the machine is switched off.
5.2.4 "ECO" button
The "ECO" mode allows to save energy when cutting
the grass, optimising the battery life. Press the button
(Fig.10.D) to enable or disable the "Eco" mode.
This mode is automatically deactivated when the opera-
tor presence levers are released.
NOTE_It is not recommended to use the "ECO" func-
tion in heavy grass cutting conditions (cutting of dense,
high, humid grass).
5.3

CUTTING HEIGHT ADJUSTMENT

Lower or raise the chassis to cut the grass at different
heights.
Carry out this operation when the cutting means is
stationary.
The cutting height is adjusted by using the designated
lever (Fig.11.A) that lifts or lowers the chassis to the desired
position.
6.

USING THE MACHINE

IMPORTANT For instructions regarding the batteries,
refer to the specific manual.
6.1 PRELIMINARY PROCEDURES
Make sure that the safety key is not inserted in its slot. Place
the machine in a stable horizontal position on the ground.
EN - 5