Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
3.4 Chimneys and flue pipes
•
A chimney can be linked to the fireplace and flue approved
for solid fuel-fired fireplaces with a flue gas temperature as
specified in «2.0 Technical data».
•
The cross-section of the chimney must be at least equal to
the cross-section of the flue. Please use «2.0 Technical data»
to calculate the correct cross-section of the chimney.
•
Several solid fuel-fired fireplaces can be connected to
the same chimney if the cross-section of the chimney is
adequate.
•
Connection to the chimney must be carried out in accordance
with the installation instructions from the supplier of the
chimney.
•
Before making a hole in the chimney the fireplace should be
test-mounted in order to correctly mark the position of the
fireplace and the hole in the chimney. See fig. 1 for minimum
dimensions.
•
Ensure that the flue pipe is inclined all the way up to the
chimney.
•
Use a flue pipe bend with a sweeping hatch that allows it
to be swept.
Be aware of the fact that connections must have a certain
flexibility in order to prevent movement in the installation
leading to cracks. N.B. A correct and sealed connection is very
important for the proper functioning of the product.
The chimney draught, see «2.0 Technical data». If the draught is
too strong you can install and operate a flue damper to control
the draught.
3.5 Assembly prior to installation
N.B. Check that the fireplace is free of any damage prior to
commencing installation.
The product is heavy! Make sure you have assistance when
erecting and installing the fireplace.
The product is delivered in a single packing case where the legs,
heat shield and door knob must be assembled.
1. Remove the cooking plate and all the separate parts inside
the stove. (Fig. 2)
2. Place the cardboard packaging on the floor and lay the stove
carefully down on its side. (Fig. 3)
3. If it is necessary to protect the walls, use the enclosed heat
shield. Use the bracket to connect the side heat shield to the
base heat shield. Fasten the bracket in the center of the base
plate with a screw.
4. The flue outlet (fig. 4) and the blanking plate exchange
positions if the smoke outlet on top of the stove is preferred.
The two screws on the flue outlet may be somewhat
difficult to release. Hold on to the nut on the inside with a
small wrench of the flue outlet to release the screws on the
outside. Ensure all possible unused flue outlets are suitably
blanked off.
5. Place the flue pipe's end outside the product's smoke outlet.
Fill any gaps between the flue pipe and smoke outlet with
suitable gasket.
6. Connect the knob (fig. 2A) to the door latch with the screw
and nut provided.
10
3.6 Control of functions (fig. 6)
When the product is set up, always check the control functions.
These shall move easily and function satisfactorily.
Jøtul F 601 N is equipped with the following controls:
Air vent control, Fig. 5A:
Left position:
closed
Right position:
open
3.7 Ash removal
•
Transfer the ashes through the door with a shovel or similar
tool.
•
Leave a little ash in the bottom of the combustion chamber
as a protective insulating layer. Ashes should be placed in a
metal container with a tight fitting lid.
For the rest, see description of how to handle ash in the Manual
on general use and maintenance in Point
measures».
4.0 Service
Warning! Any unauthorised change to the product is illegal!
Only use original spare parts!
4.1 Changing the burn plates (Fig. 7)
•
Remove the old burn plates by lifting them off the boss.
•
Brush clean the side plates in the oven before installing the
new burn plates.
•
Lift the baffle plate by the front edge.
•
Start with the left burn plate.
•
Hang the burn plate on the boss of the side plate as shown
in fig. 7A. This way the highest part of the burn plate is
supported by the ridge (fig. 7B) at the upper edge.
4.2 Changing the baffle plate
•
Remove the old baffle plate by lifting it slightly up and then
edging it down and out.
•
To reinstall, make sure the baffle plate rests securely on the
ridge in the rear (fig. 7C) and on the bosses in front.
Important note: If the baffle plate is positioned incorrectly, the
flue gas will go straight into the flue pipe. This will result in too
high flue gas temperatures, which may damage the rear plate,
and it will make heating uneconomical.
5.0 Optional Equipment
Glass door, cat.no. 320073.
«6.1 Fire preventive
Publicidad
Capítulos
