Nice mindy TT1V Instrucciones Y Advertencias Para El Instalador página 5

4.2.1) Mode I
In this mode, the command associated with the transmitter keys is fixed: key 1 (or
commands the ascent, key 2 (or
descent, key 4 (if present) commands a stop.
A single memorization stage is carried out for each transmitter; during this stage it
does not matter which key is pressed, and only one space is occupied in the
memory.
Please refer to Chapter 3 "Programming" for information about how to memorise or delete the transmitters.
4.2.2) Mode II
This mode enables the user to associate one of the following commands 1 "step step" (ascent-stop-descent-stop...), 2 "ascent", 3
"descent", 4 "stop" with the keys on the transmitter.
Memorisation must be carried out again if the user wishes to allocate another command to another key on the same transmitter.
The choice of which key to press is important during this phase, and space in the memory will be used up for each key memorised.
Example 1
Key 1
Key 2
Key 3
Key 4
Example 2
Key 1
Key 2
Key 3
Key 4
!
• The running time cannot be programmed if a transmitter is memorised in Mode II.
• A transmitter programmed in Mode II cannot be used in the "multi-group" mode.
When the memory contains no transmitters the first one can be memorized in mode II as follows:
Table "A7" Memorizing the first transmitter in mode II
1. 2 long beeps will sound as soon as the control unit is powered.
2. Press the transmitter key to be memorised within 5 seconds, and hold it down until
you hear all 3 beeps indicating memorisation has taken place, then release.
3. Within 3 seconds press the same key of the transmitter as many times as the number
corresponding to the desired command: 1 = "step-by-step" 2 = "ascent" 3 = "descent" 4 = "stop"
4. After approximately 3 seconds, the user will hear a certain number of beeps.
These beeps correspond to the command selected.
5. Press the same key again within 2 seconds to confirm programming.
Release this key when you hear the first of the 3 beeps.
N.B. 3 long beeps will sound if memorization has been successful. If, at point 4, the user does not hear the same number of beeps as the
command required, wait for a few seconds to exit the procedure, without confirming the memorisation.
one or more transmitters have already been memorized, others may be enabled in Mode II as follows:
Table "A8" Memorizing other transmitters in Mode II
1. Press and hold down the new button to be memorized until you hear a beep
(after about 5 seconds) then release it
2. Within 5 seconds, press and hold down the key of a transmitter which has already been
memorised (old) for approximately 5 seconds, until you hear 2 quick beeps, then release.
3. Within 5 seconds press the same key of the (old) transmitter as many times as the number
corresponding to the desired command: 1 = "step-by-step" 2 = "ascent" 3 = "descent" 4 = "stop"
4. After approximately 3 seconds you will hear several beeps. The number of these beeps will
be the same as the previously selected command.
5. Press the new key of the transmitter to memorise again within 2 seconds to confirm programming.
Release when you hear the first of the 3 beeps
N.B. 3 long beeps will sound if the memorization procedure has been successful. When the memory is full (30 transmitters), 6 beeps will
sound to indicate that the transmitter cannot be memorised.
) commands a stop, key 3 (or
memorization Mode II
ASCENT
DESCENT
ASCENT
DESCENT
STEP-BY-STEP on TT1V no. 1
Esempio
) Key 1 or
) commands the Key 2 or
Key 3 or
Key 4
on TT1V no. 1
on TT1V no. 1
on TT1V no. 2
on TT1V no. 2
memorization Mode II
STEP-BY-STEP on TT1V no. 2
memorization Mode
ASCENT
STOP
DESCENT
STOP
ASCENT on TT1V no. 3
DESCENT on TT1V no. 3
Example
5s
1-4 3s
1-4 3s
2s
Example
New 5s
Old 5s
Old 1-4 5s
1-4 3s
New 2s
GB
5