Dimensional Drawing - Pahlen Jet Massage Manual De Utilización

Jet Massage
Bottensugkontakt / Vacuum Point
Fit the massage nozzle and button in thin pool wall as follows:
1. Make a hole in the pool body as shown in the dimension drawing below
2. Fit the flange (1) with installation washer (2) from the inside of the pool and enclosed screw (3). NB see Figure 5.
3. Secure the self-adhesive grommet (4) on the flange.
4. Fit the pool cover and start filling the pool with water.
5. Once the water reaches approx. 5 cm below the inlet nozzle, cut a small cross in the pool cover in the centre of the hole.
Fit the grommet (8) and the sealing ring (9).
6. Cut the cover along the inner edge of the sealing ring.
7. Massage nozzle:
Loosen the cable joint (5) slightly and push in the air hose (6) a little, see Figure 4.
Securely push the end of the air hose into the rear of the nozzle (7). Press the nozzle into the inlet pipe.
Tighten the cable joint.
To connect the start button: see instruction MA25-07.
8. Fit the front (11) with the Pahlén logo facing upwards. The included nylon washers are to be attached to the screws on the
rear of the front in order to hold the screws in position in the front during future removal, e.g. during winter closure.
Tighten the front using the front screws.
9. Fill the pool with water to the desired level.
Control box
5
14
Figure 4.
5
Inlet pipe, massage (for thin pool wall).
Spa-belysning / Spa light

Dimensional drawing

- for holes in thin pool wall

78

6 (4x)
UP
2 1
3
Figure 3.
Start button with penetration (for thin pool wall).
Inloppsmunstycke / Inlet
Sugmunstycke / Outlet
UP
UP
NB 1:1 scale not used
for technical printing reasons.

78

6 (4x)
9 10
4 8
16

70-76
15
13
1
2
3

70-76
Surface treatment
E
The tolerance class in accordance with this
part of DIN 16901-
Knapp med genomföring, liner
Box 728, SE-194 27 Upplands Väsby, Sweden
Phone +46 8 59411050, Fax +46 8 59086880
Surface treatment
E
The tolerance class in accordance with this
part of DIN 16901-
Box 728, SE-194 27 Upplands Väsby, Sweden
Phone +46 8 59411050, Fax +46 8 59086880
11
ENGLISH
1. Inlet pipe
2. Installation washer
3. Countersunk screw MFT M5x30 (4x)
4. Self-adhesive grommet t = 1.5 mm
5. Cable gland
6. Air hose Ø12 (massage nozzle)
7. Nozzle
12
8. Grommet t=2mm
9. Sealing ring
10. Countersunk screw MFT M5x16 (6x)
11. Front inlet, Marine
12. Countersunk screw MFT M5x20 (2x)
13. Locking washer (2x)
11
14. Non-return valve/Filter
15. Air hose Ø4 (start button)
16. Start button
4
8 9
7
10
6
13
Designed by: Drawn by: Date
JT 2017-09-26
Assembly drawing no. Art.no.
13005541
Note!
Scale
Drawing number
UP
Designed by:
Assembly drawing no.
Inloppsrör massage, liner
UP
M12646-0
12
11
Approved by:
Revised by: Date
Rev.no.
M12805 0
Drawn by: Date Approved by:
JT 2017-09-25
Art.no. 13005540
Scale Revised by: Date
Drawing number Rev.no.
M12804 0
Flange
Sealing ring
Figure 5.