Fcc Notice; Remote Control; Troubleshooting - Envirolite EVTF1045R3-35 Instrucciones De Instalación

INSTALLATION INSTRUCTIONS (continued)
STEP 3

Place the canopy of the fixture (AA) over the outlet
box and flush against the ceiling surface.

Align the holes on the mounting bracket (II) to the
holes on the fixture (AA).

Secure the canopy of the fixture (AA) using the
canopy screws (CC).
STEP 4

Place the remote mount (GG) on the desired
location of your wall and mark the mounting holes
with a pencil.

Use a 0.25 in drill bit to drill the two holes into your
wall.

Tap in an wall anchor (EE) into each hole.
STEP 5

Align the remote mount (GG) over the holes and
secure the remote mount (GG) in place using the
anchor screws (FF).
OPERATION
NOTE: The fixture has with an internal dimmer. Do not connect the fixture to an
external dimmer. Doing so may prevent the fixture from operating as intended.
NOTE: The light switch must be on in order to control the light fixture with the remote
control.

Turn on the power at the circuit breaker or fuse box.

Turn the light switch on to activate the fixture.

REMOTE CONTROL

NOTE: Requires 2 AAA batteries (not Included)
BUTTON FUNCTIONS
Power ON/OFF.
OFF: Turns off all the lights. Other remote buttons
cannot be used in the off state.
ON: Turns the lights on and returns it to the last
settings used.
Turn the flush mount and track heads on
at the same time at 100% brightness.
Turn only the flush mount on (100% brightness).
Turn only the track heads on (100% brightness).
Dim the light up (brighten).
Dim the light down.
PAIRING FIXTURES
NOTE: The remote control can pair 1 to 4 lights at the simultaneously.
 You must be within an unobstructed distance of 2 – 3 meters (6-10 feet) to pair
your remote to your light fixture.

Long press the ON/OFF key for 5 seconds. The red indicator on the remote will
flash three times, indicating that the fixture has been paired.
REMOTE CONTROL (continued)
CC DISCONNECTING FIXTURES

Long press the ON/OFF key for 5 seconds. The red indicator on the remote will
flash five times, indicating that the fixture is no longer paired to the remote.
OPERATING DISTANCE
 An unobstructed remote can function up to a distance of 6 – 9 meters (20 – 30
feet).
AA

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the following t
wo conditions: (1) This device may not cause harmful interference; and (2) this device m
EE
ust accept any interference received, including interference that may cause undesired op
eration.
NOTE 1: This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to
HH
radio communications. However, there is no guarantee that interference can be
determined by turning the equipment off and on, the user is encouraged to try to correct
the interface by one or more of the following measures:

Reorient or relocate the receiving antenna.
GG

Increase the separation between the device and receiver.

Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
IC NOTICE
This device complies with Industry Canada's license-exempt RSSs. Operation is subject
to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.

TROUBLESHOOTING

Problem
The light will not turn on.
The product receiving information is out
of sync.
The fuse blows or circuit breaker trips
when light is turned on.
Solution
1. Make sure the power supply is on.
2. Test or replace the switch.
3. Check the wiring.
4. Check that the batteries on the remote
control are working.
5. Ensure the fixture is paired to the
remote control.
6. Ensure you are within an unobstructed
operating distance.
7. Check solutions 1-6 and confirm that
everything is correct.
8. Try to disconnect the battery to re-
power.
9. Disconnect the wall switch and power
on again.
10. Check the wire connections.